Votes - 2, Average rating: 4 ( )

Manafacture: CDA File size: 824.52 kb File name: 27fc10fe-3d14-4b76-9b7e-61845287ac3b.pdf Language of manual:

The value and times provided in this table have been obtained under laboratory conditions according to relevant standards. This information can change depending on the condition of the dishwasher’s use and environment (network tension, water pressure, water input temperature and environment temperature.) Care and Maintenance Before beginning any care or maintenance, you should always disconnect the appliance from the electricity supply, and also turn off the water supply. Door seals Wipe the dishwasher door seals regularly with a damp cloth to remove any residues. Filters You should clean the filters at least once a month. 1. Remove the lower basket. 2. Turn the microfilter anticlockwise and then lift it out as in figure 9. 3. Remove the coarse filter from the microfilter (figure 10). 4. Remove the base filter from the dishwasher compartment (figure 11). You should clean and rinse the filters thoroughly before replacing all the sections in reverse order to that above. The microfilter should lock into place once it is secure as shown in figure 12. Please note: Never run a programme without the filters in place. Incorrect fitting of the filters may reduce wash performance and potentially damage your appliance. Spray arms You should clean the spray arms at least once a month. 1. Remove the lower basket 2. Pull the lower spray arm upwards to remove it. 3. To remove the upper spray arm, first remove the nut on the upper spray arm by turning it as in figure 9. You should clean and rinse the spray arms thoroughly before replacing them. Ensure that the upper spray arm nut is securely tightened when refitting the upper spray arm. Dishwasher interior To deal with an accumulation of dirt, oil or limescale in the dishwasher, run an intensive programme with detergent when the dishwasher is empty. Alternatively, there are specialist dishwasher cleaners available that can be used. fig 9 fig 10fig 11 fig 12 Failure Codes and Troubleshooting The programme indicators also serve as a diagnostic display to help in the event of a problem with the appliance. Error code Error description Advice Wash Rinse Dry End Start/ Pause Inadequate water supply Make sure the water inlet tap is fully open. Close the water tap, separate the water inlet hose from the tap and clean the filter. Restart your machine and contact CDA service if the error continues. Continual fill error Close the tap and contact CDA service. The waste water in the machine cannot be discharged. Drain hose is blocked. The filters of your machine might be blocked. Restart the dishwasher and cancel the programme. If the error continues contact CDA service. Heater error Contact CDA service. Alarm is active against water overflow Turn off the dishwasher and disconnect from the water supply. Contact CDA service. Faulty electronic card Contact CDA service. Overheating error (temperature in Contact CDA service. the machine is too high.) Faulty heater sensor Contact CDA service. Failure Code and Troubleshooting Problem Possible cause The programme will not start Check the plug, fuse and circuit breakers of the mains supply The water tap is turned off The dishwasher door is not fully closed The water inlet filter or the machine filters are blocked Water remains inside the dishwasher at the end of the programme ed or knicked The filters are blocked The w The wThe w at atat er dr er drer dr ain hose is bloc ain hose is blocain hose is bloc k kk ed or kinked. The dishwasher stops in the middle of a programme Power failure Water inlet failure Programme is on standby Wash performance is of a low standard Poor loading of dishes hinders wash performance. Insufficient detergent added Inappropriate wash programme selected Spray arm blocked Filters clogged or incorrectly fitted Water drain pump blocked White stains on the dishes Insufficient detergent added Rinse aid setting is too low Insufficient dishwasher salt added Water softener setting is too low Salt compartment cap not completely closed The dishes are not completely dry at the end of the programme A programme without a drying stage was selected Rinse aid setting is too low Dishes unloaded too soon (allow time for drying) There are rust stains on the dishes Different sets of cutlery should be kept separate Too much salt (Water softener setting is too high) Salt compartment cap not completely closed Poor appliance earth (check mains electrical supply) The door is not opening or closing properly Door tension not correctly adjusted for the decor door Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position. How to connect an alternative plug If the fitted plug is not suitable...

Download now

Please, enter two numbers from picture: