Votes - 2, Average rating: 3
(
)
)
|
manual abstract
The multi-display now displays the number of hours without flashing. The number of hours is saved. 4. The wash programme starts automatically at the end of the delay set. Changing the start delay: As long as the wash programme has not started, you can still change the start delay set by pressing the DELAY TIMER button 0. 23 Operating instructions Load Sensing - Sensor Logic If a wash programme is started even though there are only a few dishes in the upper and/or lower rack, an intelligent electronic system adjusts the amount of water and the duration of the wash programme to the number of dishes. By this means it is possible to wash only a few dishes quickly and economically. At half load (6 place settings), up to 2 litres of water and 0.2 kWh of electricity are saved. Switching Off the Dishwasher Only switch the dishwasher off when the multi-display indicates "0" remaining programme time. 0 1. Press the ON/OFF button M. The ON/OFF button M indicator extinguishes. /1 Hot steam may escape from the appliance when opening the door immediately after the end of the programme. Therefore: 2. Open the door carefully. Emptying the Dishwasher • Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down before removing them from the appliance. • The dishes will dry quicker if, when the programme has finished, you briefly open the door fully and then leave it slightly ajar. • Leave the dishes in the dishwasher for approx. 15 minutes after the end of the programme so that they dry better and can cool down. • First empty the lower rack, and then the upper rack. By using this procedure you will avoid any water that may be remaining in the upper rack, dripping onto the dishes in the lower rack and leaving water marks. Do not under any circumstances use furniture care products or aggressive cleaners. • If necessary, clean the controls only with a soft cloth and pure warm water. • The spray arms do not need cleaning. • Occasionally check the internal containers, door seal, and water inlet for soiling, clean if necessary. Care and Cleaning 24 Operating instructions Cleaning the Filter The filters in the base of the washing compartment are to a large extent self-cleaning. Nevertheless the filters should be checked and cleaned from time to time. Dirty filters will degrade the washing result. ' 1. Open the door, remove the lower rack. 2. The dishwasher filter system comprises a coarse/fine filter, microfilter and a flat filter. Unlock the filter system using the handle on the microfilter, and remove. 3. Turn the handle about V4 a turn anticlockwise and remove. 4. Take hold of the coarse/fine filter (1) by the handle with the hole and remove from the microfilter (2) 5. Clean all filters thoroughly under running water. 6. Remove the flat filter (3) from the base of the washing compartment and clean both faces thoroughly 7. Put the flat filter back in the base of the washing compartment 8. Place the coarse/fine filter in the microfilter and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment. v Under no circumstances may the dishwasher be used without filters. 25 Operating instructions What to do, when ... Try to rectify minor faults on the dishwasher with the aid of the instructions given here. If you call in customer service to resolve one of the malfunctions listed here, or rectify an error made in the operation of the appliance, the customer service engineer's visit is not free of charge, even during the period of guarantee. ...Error Messages Are Displayed. • If the programme indicator for the selected wash programme is flashing or fault code (2 is displayed on the multi-display, you can probably rectify the fault yourself. After rectifying this fault, press the button for the wash programme that has been started. The wash programme continues. If the fault code is displayed again, contact customer service. • For all other faults, please contact customer service, stating the fault code. Malfunction The programme indicator for the selected wash programme is flashing: there is no water running into the dishwasher. Fault code (2 is displayed on the multidisplay. The programme indicator for the selected wash programme is flashing. Fault code (3 is displayed on the multidisplay. Possible Cause Remedy Tap is closed. Open tap. The filter in the threaded hose fitting is blocked. Clean the filter in the threaded hose fitting. The water inlet hose is not correctly laid. Check hose installation. The siphon is blocked. Clean siphon. The water drain hose is not correctly laid. Check hose installation. The leak prevention system has been triggered. Close the tap and contact customer service. 26 Operating instructions ...Problems Occur During Use of the Dishwasher. Malfunction Possible Cause...