Votes - 4, Average rating: 4 ( )

Manafacture: AEG File size: 1.18 mb File name: Language of manual:

For taller items, the cup racks can be folded upwards. Long-stern glasses can then be suspended from the prongs of the cup racks. ok 3(1) Fig. 16 □ After loading, push upper basket back fully into the dishwasher. 4 Setting the wash programme: □ Check that the crockery and cutlery in your dishwasher are arranged so that the spray arm is not obstructed. □ Close the door □ Open the water tap fully, if closed Important! If a wash programme has started, though the water tap Is closed, switch off the machine. Open the water tap and re-set the wash programme. Setting the Programme: □ Turn the programme indicator clockwise, according to the Programme Guide, to A, BorC, □ Turn the programme selector to the desired programme (See "Programme Guide"). The programme starts. During the wash programme, the programme indicator moves step by step, showing the stage which the programme has reached. During the heating -up of the main wash and rinse, the programme indicator remains stationary, until the required temperature is reached, Programme Correction: □ Correct a wrongly selected programme by first switching off the machine with the programme selector (setting 0). □ If the programme is already in the washing stage, ensure that there is still detergent in the dispenser. □ Set the desired wash programme once more. Interrupting the Programme: □ Awash programme in progress is interrupted when you open the door. □ Close the door. The wash programme will start again from the point at which it was interrupted. □ Only open the door during the wash cycle when absolutely necessary. By opening and closing the door cold air enters the dishwasher and quickly heats and expands. This can cause irregular operation and may require a service call. Switching off/ Removing the Dishes Switching off When the programme has ended: Turn the programme selector to ”0". Warning! When opening the door, directly after the end of the programme, hot steam can escape. Danger of scalding! Open door carefully. Note: At the end of the programme, allow the dishes to dry off completely and cool down for approx, 15 minutes in the closed machine. You can speed up the drying and cooling if you completely open the door for a moment after the end of the programme and then leave it ajar. If the dishwasher is installed under a kitchen worktop be sure that the escaping hot steam does not damage the worktop. The underside of the worktop must be protected against damage by means of an aluminium film. Removing the Dishes IWarning! Dishes are more fragile when hot. Therefore, allow the dishes to cool down before taking them out. □ First empty the lower basket, then the upper basket. In this way, you avoid water dripping from the upper basket onto the dry dishes below, GWUK ■ RS0 GB/UK Care of the machine: The front and the control panel of the dishwasher should be cleaned only with a soft cloth and warm, clean water. Warning! Do not use furniture polish or abrasive cleaning agents. The spray arms do not need to be cleaned. The interior, door seal and top spray arm connection should periodically be inspected for soilage and if necessary cleaned. Cleaning the Filters The filter assembly in the bottom of the dishwasher must be regularly checked for soilage and cleaned when necessary. Dirty filters reduce the efficiency of the wash. Warning! After a wash programme is complete, the heating element at the bottom of the dishwasher remains hot. Danger of bums! Do not touch the heating element. O Open the door, pull out the lower basket. □ The filter assembly in the dishwasher has 3 parts. (Coarse filter, microfilter and surface mesh). The complete filter assembly can be released and removed by means of the handle on the microfilter. □ Turn the handle of the filter assembly a quarter of a turn anticlockwise and lift out. □ Grip the coarse filter (1) by its handle and separate it from the microfilter (2). □ Thoroughly clean all filters under running water, □ Take surface mesh (3) out of the bottom of the dishwasher and thoroughly clean both sides. □ Replace the surface mesh in the bottom of the dishwasher, ensuring that it is correctly positioned in the bottom of the dishwasher. □ Reassemble the coarse filter in the microfilter, snap together and replace the complete assembled unit into the surface mesh. Use handle to turn clockwise until locking position is found. Please check whether you can solve the smaller problems with the machine yourself, by means of the following advice. If the advice does not help, please contact the AEG Customer Service Department. □ Drainage pump continually running • even when the machine is turned off. - The flood protection system has activated. First, close the water tap, then pull out the plug. In case of hard-wiring: turn off the electricity supply, remove the fuse and disconnect. Telephone the AEG Customer Service Department to register the fault. □ The programme does not start. - Are the ...

Download now

Please, enter two numbers from picture: