Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
The cutlery basket (Figures A) Insert the cutlery into the basket: knives and utensils with sharp blades or tips should be positioned with the sharp parts at the bottom. Position all cutlery items so that they don't touch. If the rack has side baskets, the spoons should be loaded individually into the appropriate slots (see fig. A). -Especially long utensils should be placed in the horizontal position at the front of the upper rack. How to use the upper rack Place delicate and lightweight dishes in the upper rack: glasses, tea cups and coffee cups, saucers - but plates too -shallow salad bowls, slightly dirty frying pans and shallow pans (the photo illustrates a few examples). Position lightweight dishes in such as way as to avoid their being moved by the spray of water. -The upper rack can be equipped with one or two special tip-up compartments for mugs and cups, as well as spoons, knives and forks, which should be fitted in the slots provided. Stemmed glasses can be hooked onto these compartments by threading the stems into the slots provided (see fig. D). After loading the dishes, remember to check that the blades on the sprayer arms can turn freely without knocking against any dishes. How to adjust the upper rack …. The upper rack can be set in a high or low position. To do so, open the rail stop flaps and pull the rack out completely; now place it with the back wheels in high or low position, then slide it along the guide rails until the front wheels also go in; now close the rail stop flaps (see fig. F). Load examples lower rack upper rack fig. D AA 1 2 3 4Fig. F 5 GB Turning on the Appliance First of all After performing all the operations described in the previous paragraphs, turn the water tap on completely and press ONOFF button "A": you will hear a short beep, the display lights up and the wash cycle time selected on the knob will flash. Selecting and starting a wash cycle. • Select the desired wash cycle by turning knob "D" clockwise from wash cycle 1 to 7 and anticlockwise from 7 to 1; the display indicates the average duration of the wash cycle and the cycle phases it consists of (consult the wash cycle table contained on page 7, especially when first using the appliance). • Press the Start button "R" and the wash cycle starts up, emitting a double beep; the approximate amount of time left until the end of the wash cycle is displayed. • If the time indicated at the start of the wash cycle does not correspond to the actual duration of the cycle itself, this could be for a number of reasons: the temperature of the inlet water, the degree of soil, prolonged attempts by the appliance to clean the wash filter from food residue clogging it, etc. Cycle phase under way indicator While the wash cycle is under way, the symbols corresponding to the cycle phases light up in sequence. Here are the symbols corresponding to each cycle phase: Pre-wash Wash Rinses Drying Cancelling and modifying a wash cycle in progress Premise: a wash cycle in progress can only be modified if it hasn't been running for long. Keep the Reset button "R" pressed for about 3 seconds: a prolonged beep will sound, followed by three short beeps. The cancelled cycle time will flash on the display. Turn the knob to select a new wash cycle. You've left out a dish? You can interrupt a wash cycle by pressing the "ON-OFF" button, then place the forgotten dishes into the appliance, which will start up, after approximately 10 seconds, from where it was interrupted when you turn it back on. There's been a power failure? Has the dishwasher door been opened? The wash cycle stops and 3 dashes appear on the display; the cycle restarts as soon as the electricity comes back on or when the door is shut. At the end of the wash cycle The end of the wash cycle is indicated by two short beeps and the word "END" flashes on the display. Warning: Turn the appliance off by pressing button “A”, unplug the appliance from the electricity socket to cut off the power supply; the power supply cable should consequently be easily accessible. • Turn off the water tap. • Empty the lower rack first. Make sure the wash cycle has ended before removing the dishes! Warning: when you open the dishwasher door after the wash cycle has just ended or is under way, take care not to scald yourself with the hot steam. How to set the extra drying Press button "E". After a prolonged beep, indicator light "G" lights up and the time corresponding to the wash cycle selected on the knob will flash on the display. Note: The time indicated on the display is extended due to the extra drying time. To disable the extra drying option, press the same button and indicator light "G" will be turned off after a beep is sounded. This option is incompatible with the soak cycle. GB 6 Setting a half load and a delayed start How to set a delayed start When you have loaded the dishes, you can choose when to start your dishwasher before setting the wash cycle desired. • Press button "G" repeatedly to po...
Other models in this manual:Dishwashers - IDE 1005 (400.34 kb)