Votes - 5, Average rating: 4.6
(
)
)
|
manual abstract
Position lightweight dishes in such as way as to avoid their being moved by the spray of water. The upper rack can be equipped with one or two special tip-up compartments for mugs and cups, as well as spoons, knives and forks, which should be fitted in the slots provided. Stemmed glasses can be hooked onto these compartments by threading the stems into the slots provided (see fig. D). After loading the dishes, remember to check that the blades on the sprayer arms can turn freely without knocking against any dishes. How to adjust the upper rack …. The upper rack can be set in a high or low position. To do so, open the rail stop flaps and pull the rack out completely; now place it with the back wheels in high or low position, then slide it along the guide rails until the front wheels also go in; now close the rail stop flaps (see fig. F). Load examples Bottom Rack Top Rack AA GB 1 2 3 4Fig. F fig. D 5 Turning on the Appliance How to start a wash cycle… After performing all the operations described in the previous paragraphs, turn the water tap on completely and press ONOFF button "A": you will hear a short beep and indicator light "B" lights up. At this point, the appliance is on and ready to be programmed Starting and selecting the cycle. Turn the cycle selector knob "D" clockwise until the reference notch on the knob corresponds with the number or symbol for the cycle you wish to set (consult the wash cycle table on page 7, especially when first using the appliance). If the appliance door is shut, press the Start button "R" and you will hear a beep; the cycle will start up within a few seconds. Cycle phase indicator lights The dishwasher is provided with 4 indicator lights "G" which come on in sequence as the appliance is performing that specific phase of the wash cycle. These phases are: pre-wash, wash, rinses, drying Note: the rinses light is also used to indicate the 3-in-1 button activation. Cancelling or modifying a wash cycle in progress….. Premise: You can cancel the wash cycle in progress, if it has only just started. To modify a wash cycle, keep the RESET button "R" pressed for about 5 seconds: a prolonged beep will sound, followed by three short beeps. Indicator light "G" will turn off and at this point, all the settings will have been cancelled. To select a new wash cycle, repeat the operations illustrated in the paragraph entitled "starting and selecting the cycle". If you have left out a dish… You can interrupt a wash cycle by pressing the ON-OFF button, then place the dishes you had left out into the appliance, which will start up from where it was interrupted when you turn it back on. There's been a power failure? Have you opened the dishwasher door? The wash cycle stops and then restarts when the electricity comes back on or when the door is shut. At the end of the wash cycle…. The end of the wash cycle is indicated by two short beeps and the flashing of the drying phase indicator light. Warning: Turn the appliance off by pressing button “A”, unplug the appliance from the electricity socket to cut off the power supply; the power supply cable should consequently be easily accessible. • Turn off the water tap. • Wait a few minutes before unloading the dishes: if you wait a little while, they dry better thanks to the steam. • Empty the lower rack first. Warning: when you open the dishwasher door after the wash cycle has just ended or is under way, take care not to scald yourself with the hot steam. 3-in-1 button. Press before selecting a cycle. If you press this button when you are intending to use 3-in-1 tablets (detergent + salt + rinse aid), the washing and drying performance of your dishwasher will be greatly improved. When this function is selected, the overall cycle time will increase by approximately 15 minutes. When the button has been activated correctly, you will hear a prolonged beep and the indicator light "G" will light up. When the button has been deactivated, you will hear a short beep and the 3-in-1 indicator light will switch off. • When the cycle begins, the 3-in-1 indicator light will switch off. • The 3-in-1 option is cancelled automatically at the end of each cycle. This button cannot be used in conjunction with the quick wash and soak cycles. You want to wash on one rack only? Remember to use half the amount of detergent. Your dishwasher also allows you to wash half a load on the upper rack only, to save water and electricity. Before setting any wash cycle, press button "I", the indicator light "L" lights up. GB 6 Wash Cycle Table Dishwasher washing guarantees your dishes will be cleaned in a hygienic setting for safer, cleaner results. &\FO. &\FOHVHOHFWLR. LQVWUXFWLRQ. &\FOHGHVFULSWLR. 'HWHUJHQ. IRUSUH. ZDVK. ZDV. 5LQV. $L. :DVKF\FO. GXUDWLR. WROHUDQF. .. ,QWHQVLY. Very dirty dishes and pans (not to be used for delicate items). Pre-wash with hot water at 40°C Wash at 65°C. 2 cold rinses Rinse with hot water at 70°C. Drying. Powder 5+25 gr. --------Tablets 1+1 . . 7LPH
Dishwashers - IDL 735 (434.8 kb)