Votes - 5, Average rating: 4 ( )

Manafacture: Frigidaire File size: 1.42 mb File name: Language of manual:

Note: Hard water may cause lime deposi. buildup on the interior of the dishwasher. Fo. cleaning instructions see .Removing Spots an. Film. section. Overfill Protector.keeps dishwasher fro. overfilling and is located in the left fron. corner of the tub. . Clean occasionally with household cleane. containing vinegar o. bleach to dissolve an. buildup. . Overfill Protecto. should move up an. down freely about on. inch. If it does no. move, lift and clea. underneath. Care of Drain Air Ga. If a drain air gap was installed for your built-i. dishwasher, check to make sure it is clean s. the dishwasher will drain properly. A drain ai. gap is usually mounted on countertop an. can be inspected by removing the cover. This i. not part of your dishwasher and is not covere. by warranty. Property Damage Hazar. Freezing temperatures may cause wate. lines to rupture. Be sure all supply lines t. and circulating lines within dishwasher ar. protected. Failure to do so could result in propert. damage. Winterizin. A dishwasher left in an unheated place shoul. be protected from freezing. Have a qualifie. person do the following. To Disconnect Service. 1. Turn off electrical power to the dishwashe. at the supply source by removing fuses o. tripping circuit breaker. 2. Shut off water supply. 3. Place a pan under the inlet valve. Disconnect water line from inlet valve an. drain into pan. 4. Disconnect drain line from pump and drai. water into pan. To Restore Service. 1. Reconnect the water, drain, and electrica. power supply. 2. Turn on water and electrical power supply. 3. Fill both detergent cups and ru. dishwasher through a NORMAL cycle. 4. Check connections to make sure they d. not leak. Note: See Installation Instructions for mor. details. 13 Changing Color Panels Some models come with reversible door panel inserts. To change the color panel: 1. Remove snap-on bottom trim by pulling forward. Support color panel(s) at bottom while removing trim. Slide color panel(s) downward 1/2.. 2. Grasp top and bottom of panel(s) and bow slightly until they are clear of trim. DO NOT REMOVE SPACER. 3. Arrange panel(s) so desired color is facing out. Place one side of panel under side trim and bow slightly until other side fits under opposite trim. Slide panel(s) up to fit under control panel. 4. Replace bottom trim by fitting slot over bottom edge of door and press to secure. Customized Wood Panels Your dishwasher can be customized with 1/4. wood panels. Refer to your installation instructions for more information. Bottom Trim Spacer STEP 2 STEP 4 Color Panel(s) Side Trim Control Panel Color Panel(s) Color Panel(s) Bottom Trim Bottom Edge of Door STEP 1 STEP 3 Metal door panels are sharp and should be handled with care. Wear gloves to protect hands. Failure to do so can result in injury. Cut Hazard Solutions to Common Dishwashing Problem. Before calling for service, review this list. It may save you both time and expense. This list includes common experience. that are not the result of defectiv. workmanship or material in you. dishwasher. Food Soils Left on Dishe. . Choose another cycle for longer washin. time. . Check rack loading section for prope. loading.avoid nesting items. . Home water pressure may be too low. should be 20 to 120 pounds per squar. inch (psi). . Check incoming water temperature. I. should be at least 120°F (49°C). (See Factor. Affecting Performance.. . Check water hardness. For extremely har. water, it may be necessary to install a wate. softener. (See Detergent Chart.. . Use fresh detergent. . Check to make sure funnel in top rack is no. blocked. . Make sure items are not blocking the spra. arms, preventing them from rotating. . Check to see if the rinse aid dispenser need. refilling. Dishes not Dr. . Select Hot Dry option. . Make sure the rinse aid dispenser is filled. . Increase the amount of rinse aid. (See Rins. Aid.. . Check the incoming water temperature. B. sure it is at least 120°F (49°C). . Check for proper loading.avoid nestin. items. . Plastic items may need to be towel dried. . Cups with a concave bottom will collec. water. Glassware/Flatware Spotted or Cloud. . Check water hardness. For extremely har. water, it may be necessary to install a wate. softener. (See Detergent Chart.. . Water temperature may be low. Avoi. extremely low or high temperatures. (Se. Factors Affecting Performance.. . Avoid overloading and improper loading. (See Preparing and Loading Dishes.. . Use fresh detergent. Old detergent i. ineffective. . Make sure rinse aid dispenser is filled. . Check to see that proper amount o. detergent is being used for cycle selected. Also, check phosphate level. (See Detergen. Dispenser.. . Home water pressure may be too low.i. should be 20 to 120 pounds per squar. inch (psi). Dishware Chippe. . Load with care and do not overload. (Se. Preparing and Loading dishes.. . Place delicate items in top rack. . Place glasses securely against pins and no. over pins. . Load items so they are secure and don.t ja. lo...

Download now

Please, enter two numbers from picture: