|
manual abstract
• Water and power supply should enter in the shaded area. • Electrical and water connections are at the right front of the dishwasher. The hot water line should extend forward 30" to 40" from the rear wall. The electrical must extend forward at least 24" to reach the junction box. • To prevent siphoning, an air gap must be used when the waste tee or disposer connection is less than 18" above the floor. Cabinets Square and Plumb Floor MUST be Even with Room Floor This Wall Area must be Free of Pipes or wires 34-1/2" Min. Underside of Countertop to Floor 24" Min. 24" Min. 5" 5" 4" 4" 6" 24" *24" 34" Adjustableto 35" *dishwasher models ZBd6890 and ZBd0700 require a 3/4" thick custom panel and will be 24-3/4" deep. Electrical Requirements The dishwasher must be supplied with 120V, 60Hz, and connected to an individual properly grounded branch circuit protected by a 15-or 20-amp circuit breaker or time-delay fuse. For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000. Custom Panel for Model ZBD0700NII These dishwashers require a field installed 3/4” thick custom panel and custom handle. An installation template is packed with these models and may be obtained in advance. Order Pub. No. 31-30569-1. Complete panel installation instructions are included on the template. CUSTOM PANEL SIZE REQUIREMENTS HEIGHT Panel height must be between 30-1/16" and 30-1/4". 30-1/16" Min. 30-1/16" Min. 30-1/4" Max. 23-3/4" 30-1/4" Max. • If the panel height is more than 30-1/4” it will prevent the door from swinging open. • If the panel height is less than 30-1/16” it will not cover the 23-3/4" dishwasher door frame. • The top of the custom panel must be flush with the top of the door. The 1/2” minimum gap between the top of the door and the bottom of the countertop must be maintained. Countertop WIDTH Panel width must be 23-3/4". Minimum 1/2" gap for ClearanceCountertop 1/2" min. Minimum 1/2" gap for Clearance 1/2" min. • If the panel width is less than 23-3/4” it will not cover the dishwasher frame. IMPORTANT: To ensure optimum door balance performance, the custom panel must not weigh more than 14 lbs. Accessories for custom panel model ZBD0700 ZPR0700S door panel provides a professional-style handle on a stainless steel door panel. ZTB700 stainless steel tubular handle for installation onto a custom panel. Before installing refer to installation instructions for details. Pub. No. 31-30586 As an EnErgy StAr® Listed by partner, gE has determined Underwriters that this product meets the Laboratories EnErgy StAr guidelines for energy efficiency. Specification Revised 2/08 150048 ZBd0710NSS/ZBd0700NII GE Monogram® Fully Integrated Built-In dishwasher Custom Dishwasher Door Panel Template GE PuB. No. 31-30569-1 Top of Panel Top of PanelTrim Around Dotted Line 11-5/16" Trim Around Dotted Line 2-9/32" 25-9/16" 11-5/16" 2-9/32" 25-9/16" Drill 3/32" Pilot Hole 3/32" Deep Drill 3/32" Pilot Hole 3/32" Deep Drill 3/32" Pilot Hole 3/32" Deep Drill 3/32" Pilot Hole 3/32" Deep 3/4 Thick Custom Panel Template Instructions for Top Control Integrated Profile and Monogram Dishwasher Models The custom panel should be sized to your installation situation. See Step 1. For easier installation the custom panel and custom handle should be attached before installing the dishwasher. Use this template to locate mounting screws and spacers on the custom panel. IMPORTANT • A custom handle must be installed onto the custom panel. Install the custom handle 4-1/2" max. from the top of the panel. STEP 2 DRAW CENTERLINE • Place the custom panel on a flat surface with appearance side down. • Locate the vertical center of the panel at the top. • Use a carpenters square to draw a centerline from top to bottom. STEP 4 INSTALL MOUNTING SCREWS AND SPACERS Mark Center Screw Holes STEP 5 INSTALL CUSTOM HANDLE A custom handle must be installed onto the panel before the panel is secured to the dishwasher door. • The handle should be installed so that it aligns with adjacent drawer handles, or 4-1/2" max. from the top of the panel. Secure the handle in the same manner as cabinet handles. Screws must be countersunk into the panel. S...
Other models in this manual:Dishwashers - ZBd0710NSS (203.01 kb)