Votes - 4, Average rating: 3.3 ( )

Manafacture: GE Monogram File size: 1.18 mb File name: Language of manual:

CleanSteel Door Panel (model numbers ending in CS) Use a clean, soft, lightly dampened cloth, then dry thoroughly. Do not use appliance wax, polish or any chemical agent on CleanSteel doors. Do not wipe the dishwasher with a soiled dish cloth or wet towel. These may leave a residue. Do not use scouring pads or powdered cleaners because these products can scratch the finish. Cleaning the Control Panel To clean the control panel, use a lightly dampened cloth. Then dry thoroughly. Protect Against Freezing If your dishwasher is left in an unheated place during the winter, ask a service technician to: Drain water from the water inlet line and water valve. (Use a pan to catch the water.) Cut off electrical power to the dishwasher. Remove fuses or trip circuit breaker. Reconnect the water inlet line to the water valve. Turn off the water supply and disconnect the water inlet line from the water valve. 3 1 4 2 Air gap Check the air gap any time your dishwasher isn’t draining well. Does Your Dishwasher Have an Air Gap? An air gap protects your dishwasher The air gap is easy to clean. against water backing up into it if a drain 1 Turn off the dishwasher and lift off clogs. The air gap is not a part of the the cover. dishwasher. It is not covered by your warranty. Not all plumbing codes require 2 Remove the plastic cap and clean air gaps, so you may not have one. with a toothpick. 12 Problem Possible Causes What To Do Dishes and flatware Low inlet water temperature • Make sure inlet water temperature is correct (see page 8). Turn on not clean the hot water faucet nearest the dishwasher, let run until the water temperature stops rising. Then start the dishwasher and turn off the faucet. This insures the entering water is hot. Water pressure is temporarily low • Turn on a faucet. Is water coming out more slowly than usual? If so, wait until pressure is normal before using your dishwasher. Air gap or disposer is clogged • Clean the air gap or flush the disposer. Improper rack loading • Make sure large dishware does not block the detergent dispenser or the wash arms. See the Loading the dishwasher racks section. No air gap or high drain loop • Verify that you have an air gap or a high drain loop. Refer to the Installation Instructions. Spots and filming • Use Jet-Dry® or Cascade Crystal Clear® rinse agents to remove spots and on glasses and prevent new film buildup. flatware • To remove stubborn spots and pre-existing film from glassware: 1 Remove all metal utensils from the dishwasher. 2 Do not add detergent. 3 Select the POTS & PANS cycle. 4 Start the dishwasher and allow to run for 18 to 22 minutes. Dishwasher will now be in the main wash. 5 Open the door and pour 2 cups (500 ml) of white vinegar into the bottom of the dishwasher. 6 Close the door and allow to complete the cycle. If vinegar rinse doesn’t work: Repeat as above, except use 1/4 cup (60 ml) of citric acid crystals instead of vinegar. Cloudiness on Combination of soft water and • This is called etching and is permanent. To prevent this from happening, glassware too much detergent use less detergent if you have soft water. Wash glassware in the shortest cycle that will get them clean. Water temperature entering • This could be etching. Lower the water heater temperature. the dishwasher exceeds 150°F Suds in the tub Correct detergent • Use only automatic dishwasher detergents to avoid sudsing. wasn’t used Cascade® and Electrasol® Automatic Dishwashing Detergents have been approved for use in all GE dishwashers. • To remove suds from the tub, open the dishwasher and let suds dissipate...

Download now

Please, enter two numbers from picture: