Votes - 4, Average rating: 3.3
(
)
)
|
manual abstract
The Time Zone is set CLOCK • Press and hold MODE button for 3 seconds: the year will flash. Press UP ( ^ ) or DOWN ( Ў ) to change flashing digits. • After the year is set, press MODE button to confirm and move to the 22 21 next parameter ( month) • Continue setting month, date, hour, minutes, language for the day of the week and temperature in Fahrenheit or Celsius • Press MODE for the last time to return to the time of day with seconds, after the last parameter is set CLOCK ALARMS The Barometric Weather Forecaster has two time alarms – Weekday alarm ( W) and Single day alarm( S) - and one Ice Warning Alarm ( PRE- AL). • If Weekday ( W) alarm is activated, it will sound at the set time and the alarm icon will flash Mondays through Fridays • If Single (S) day alarm is activated, it will sound at the set time and the alarm icon will flash only for this specific day and will not activate on subsequent days • If Ice Warning Alarm ( PRE-AL) is activated, in will sound at the set time and alarm icon will flash once the remote temperature for Channel One (1) will reach 32°F(0°C) and below NOTE: Ice Warning Alarm can be set only if one or both - Weekday or Single alarm - are programmed. SETTING THE WEEKDAY (W) AND SINGLE DAY ( S) ALARMS • Press ALARM button once to enter into the alarms setting mode. The default alarm is a Weekday alarm ( W). The abbreviation “ OFF” with a letter “ W” next to it will be displayed, if the alarm has not been set previously • Press and hold ALARM button for two seconds. The hour digit will flash • Adjust the hour using UP ( ^ ) or DOWN ( Ў ) buttons 23 • Press ALARM button again. The minute digits will flash • Adjust the minutes using UP (^ ) or DOWN (Ў ) buttons • Press ALARM button again to confirm and the weekday alarm time will be set • Set Single (S) day alarm if desired in the same manner SETTING THE ICE WARNING ALARM (PRE- AL) If Weekday (W) or Single day (S) alarm is set, the Ice Warning Alarm (Pre-AL) can be programmed. • Press ALARM button once to enter into the Ice Warning Alarm setting mode. The abbreviation OFF with a PRE- AL next to it will be displayed. • Press and hold ALARM button for two seconds. The number 30 will flash, meaning that if selected, the alarm will sound 30 minutes earlier than the Weekday or Single alarm. • Select the desired Ice Warning Alarm interval in 15 minutes increments between 15 and 90 minutes, using UP ( ^ ) or DOWN (Ў )buttons • Press ALARM button to confirm and exit from the alarm setting mode. ACTIVATING THE ALARM • Press ALARM button to enter into the desired alarm mode. • Press UP ( ^ ) to activate or DOWN ( Ў ) to deactivate desired alarm. When alarms are activated, the corresponding icons W, S or PRE-AL will be displayed. SNOOZE When the time alarm sounds, press the SNOOZE/LIGHT button to temporarily stop it. After the SNOOZE/LIGHT is depressed, the time alarm sound will resume in four minutes. 24 23 If the alarm is not disabled after that, it will sound for two more minutes and then will stop by itself. BACKLIGHT The backlight feature is enabled only after the time is set. To activate the backlight press the SNOOZE/ LIGHT button once, and both – clock and weather station displays - will light up for five seconds. TROUBLESHOOTING Check here before contacting customer service. Issue Symptom Solution Main unit US Atomic Time signal is not received Place unit by the window and keep it there overnight Main unit The weather readings weather station are different from the TV, radio or official weather reports The weather data may vary considerably due to different environmental conditions and placement. Check the placement tips included in this manual to site your weather sensors in the best possible way. Remote sensor Cannot locate remote sensor Check batteries Check location Press and hold DOWN ( Ў ) button on the main unit to search for the signal from the remote sensor Cannot change the channel Press “ RESET” after setting the channel Cannot change the C° to F° and back Press “ RESET” after setting C/ F Data does not match data on the main unit Initiate manual sensor search (Press and hold DOWN ( Ў ) button on the main unit) 25 PRECAUTIONS This product is engineered to give you years of satisfactory service if handled carefully. Here are a few precautions: • Do not immerse the units in water. • Do not clean the units with abrasive or corrosive materials. They may scratch the plastic parts and corrode the electronic circuits. • Do not subject the product to excessive force, shock, dust, temperature, or humidity, which may result in malfunctions, shorter lifespan, damaged batteries, and damaged parts. • Do not tamper with the units internal components. Doing so will invalidate the warranty and may cause damage. These units contain no user-serviceable parts. • Use only fresh batteries. Do not mix new and old batteries. • Read the user's manual thoroughly before operating the units. SPECIFICATIONS Main Unit Radio Frequency: 433 MHz RF Recep...