|
manual abstract
VIEWING REMOTE (CHANNEL) TEMPERATURE AND HUMIDITY Static Display: In Temperature and Humidity Window, press the CHANNEL button to recall a different channel. Channel Auto-Scan Display: To enable automatic scan of the different channels, press and hold CHANNEL, until the .. icon is displayed. Each valid channel will be alternately displayed with a 5 seconds delay. NOTE: the channel auto-scan feature can be active only if there are more than one remote sensors operating and are set to different channels. RECALLING TEMPERATURE AND DEW POINT INFORMATION In Temperature and Humidity Window press SET button recalling either: • Temperature and relative humidity • Dew point and relative humidity PROGRAMMING TEMPERATURE IN CELSIUS OR FAHRENGEIT In Temperature and Humidity Window, press and hold SET to toggle the temperature in Celsius (. C) or Fahrenheit (. F). ACTIVATING OR DEACTIVATING ALARMS In Temperature and Humidity Window, press the ALARM to recall a current temperature for the corresponding channel, the upper temperature alert with ^ icon (if disabled, displays OFF), or lower temperature alert with Ў icon (if disabled, displays OFF). 33 Once the above alerts are displayed, press the UP or DOWN to enable or disable the corresponding alert. PROGRAMMING ALARMS • In the Temperature and Humidity Window, press ALARM selecting the desired alarm. • Press and hold ALARM button until the remote temperature and ^ or Ў icon starts flashing. • Adjust the temperature digits for the Temperature Alarm using the UP or DOWN. Press and hold either button for fast digits advance • Press the ALARM to confirm selection and return to the temperature alarm selection screen VIEWING REMOTE TEMPERATURE AND HUMIDITY MAX/MIN READINNGS In the Temperature and Humidity Window press the MEMORY button recalling: • Current temperature and humidity • Minimum temperature and humidity • Maximum temperature and humidity at the remote location. RESETTING REMOTE TEMPERATURE AND HUMIDITY MEMORY In the Temperature and Humidity Window, press and hold MEMORY button to clear memory for all channels. REMOTE SENSORS STATUS The wave icon above the current channel icon shows the connection status of the corresponding remote sensor: Icon Status 34 33 Searching for the signals from the remote sensor Corresponding remote sensor signal received successfully No signals received for over 15 minutes ALL REMOTE SENSORS SIGNAL ACTIVATION The main unit can be manually activated to search for the signals from remote sensors by pressing and holding DOWN button. WIND WINDOW The left section of the Wind Window can be programmed to display either a temperature at the place of anemometer or the temperature adjusted to the wind chill factor. The right section of the Wind Window indicates the average wind speed for the past 10 minutes, as well as gust, high wind speed and gust alarm information. It can also show records of the maximum wind speed and wind gust collected during the day. The wind speed and gust can be programmed to alert you if the wind speed or gust exceeds a pre- set limit. The wind speed can be displayed in km/h, mph, m/ s or knots. ACCESSING Press UP or DOWN until the WIND icon on the display starts flashing. OPERATING In the Wind Window press the SET button to recall: • Wind chill temperature with wind speed 35 • Temperature at anemometer with wind speed PROGRAMMING UNITS In the Wind Window, press and hold SET to set the wind speed units in km/h, mph, m/s or knots. VIEWING STATISTICS In the Wind Window, press the MEM button to recall: • Current wind speed, a daily maximum wind speed with “ DAILY MAX” displayed, a gust speed with a “ GUST” displayed and a daily maximum gust speed with a “ GUST DAILY MAX” displayed. RESETTING STATISTICS MEMORY In the Wind Window, press and hold MEM to reset all wind statistics. ACTIVATING OR DEACTIVATING ALARMS In the Wind Window press ALARM to recall • Current wind speed • Wind speed alarm with the “ ALARM HI” displayed • Wind gust alarm with the “GUST ALARM HI” displayed • Daily maximum wind speed with “ DAILY MAX” displayed If the specific alarm is disabled, “OFF” will be displayed; otherwise the alarm value will be shown. When the wind alarm is displayed, press the UP or DOWN to activate or deactivate it. PROGRAMMING HIGH WIND ALARM • In the Wind Window, press ALARM to select the desired alarm (wind 36 35 speed or wind gust speed) • Press and hold ALARM button until speed digit will flash. • Set the alarm using the UP or DOWN. Press and hold either button for fast digits advance. • Press ALARM to confirm your selection and return to the high wind alarm selection screen. MAINTANANCE CHANGING BATTERIES The battery status of each weather sensor is checked every hour. If the low battery indicator lights up, replace the batteries in the corresponding unit. CHANGING BATTERIES IN THE MAIN UNIT • Remove the battery compartment door from the back and replace batteries. Do not mix old and new batteries • Replace the battery compart...
Other models in this manual:Weather Radios - TE852W (369.66 kb)
Weather Radios - TE852ELW (369.66 kb)