Votes - 5, Average rating: 4
(
)
)
|
manual abstract
The VMCC1 is designed to mount a center channel speaker below a Sanus VMSA, VMAA, VMAA18, VMAA26, VMDD or a VMDD26 Flat Panel Wall Mount. Safety Warning: If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly to you. Never use defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified by Sanus Systems. Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of purchase. Required Tools: Phillips screw driver and crescent wrench. Supplied Parts and Hardware: Hardware shown as actual size. (1) Left Upper Extension - a (1) Right Upper Extension- b (2) Lower Extension - c (2) Axis Bracket - d (2) Bar Bracket - e (2) Speaker Bracket - f (1) Support bar - g (2) M4 x 10 Bolt - h (2) M5 x 10 Bolt - i (10) 1/4 - 20 x 3/8 Bolt - j (10) 1/4 - 20 x 5/8 Bolt - k (2) Spacer - l (8) 1/4 - 20 Nut - m (2) 1/4 - 20 x 1500 Bolt - n Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 11.16.05 Customer Service: 800.359.5520. See complementary Sanus products at VMCC1ins_010606_ML.indd 3 1/16/06 10:31:51 AM ENGLISH For assembly information for the VMSA, VMAA, VMAA18 and VMAA26 see the Steps 1 through 6. For assembly information for the VMDD and VMDD26 see Steps 7 through 12. Step 1: Remove mount from Wall Plate and remove lower Cross Tube from the mount assembly. Remove the mount from the wall plate. Loosen the Allen Bolts in the lower three Vise Assemblies and remove the lower Cross Tube from the mount assembly. See Diagrams 1a and 1b below. Diagram 1a Diagram 1b vise assemblies cross tube Step 2: Add Axis Brackets Position the Axis Bracket (d) so it fits over the Axis Assembly on the mount. Insert a 1/4 - 20 x 5/8 Bolt (k) through the Axis Bracket, Axis Assembly and into a 1/4 - 20 Nut (m). Repeat process until the Axis Bracket is secured with four 1/4 - 20 x 5/8 Bolts and four 1/4 - 20 Nuts. Tighten each Bolt with a phillips screw driver until secure. See Diagram 2 below. Detailed View Diagram 2 m k axis assembly d VMCC1ins_010606_ML.indd 4 1/16/06 10:31:53 AM ENGLISH Step 3: Add Bar Brackets Slide the lower Cross Tube through the Bar Bracket (e), the Axis Assembly, a second Bar Bracket and through the second Monitor Bracket. Tighten all three Vise Assemblies secure the Cross Tube once it is slid through the second Monitor Bracket. See Diagram 3 below. Diagram 3 monitor bracket monitor bracket e axis assembly cross tube e Step 4: Add Support bar Slide the Support Bar (g) through the Bar Bracket (e), Axis Bracket (d) and through the other Bar Bracket. Make sure the Support Bar is centered on the wall mount. Thread each 1/4 - 20 x 5/8 Bolt (k) through each hole in the bottom of the Axis Bracket until they bottom out in the Support bar. See Diagram 4 below. Diagram 4 Detailed View g d e e k VMCC1ins_010606_ML.indd 5 1/16/06 10:31:55 AM ENGLISH Step 5: Configure Speaker Attachments Configure the Speaker Attachments as shown in the Diagrams below. Tighten all Bolts with a Phillips screw driver. Repeat process for the second Speaker Attachment. The Extension assemblies can be adjusted vertically to adjust the vertical position of the speaker. The depth of the speaker can be adjusted by using the front set of holes or the back set of holes in the Speaker Bracket (f). The Upper Extensions can be adjusted using the slot in the top to adjust the depth of the speaker. Note: In rare occasions, the Lower Extensions may not be used. In this case, Speaker Bracket (f) may be attached directly to the Upper Extensions (a,b) Configuration 1 Configuration 2 a b j j c c f j j f Step 6: Add Speaker Attachments to assembly Thread a 1/4 - 20 x 3/8 Bolt (j) up through each Upper Extension (a,b) and into the Bar Bracket (e). Tighten to secure the Upper Extension. Thread a 1/4 - 20 x 5/8 Bolt (k) up through each of the Upper Extensions. Do not tighten the 1/4 - 20 x 5/8 Bolts at this time, you will tighten these so they bottom out into the Support Bar after the speaker is attached. Note: For Speakers that have threaded inserts that are spaced between 1.75 inches and 15.5 inches use configuration 1. If the threaded inserts on the speaker are spaced wider than 15.5 inches, the tabs on the Speaker Brackets should face away from each other. In Diagram 6, Speaker Brackets shown facing toward each other. Detailed View Diagram 6 e a,b j k VMCC1ins_010606_ML.indd 6 1/16/06 10:31:57 AM ENGLISH Assembly Instructions for the V...