Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
You have selected the finest in residential wood pellet heating technology. This OPERATIONS GUIDE will walk you through the initial setup of your pellet stove, from first light to fine tuned adjustments. We have also included detailed information on cleaning and maintenance as well as wood pellet fuel facts. Please note the following points regarding stove installation and pellet heating in general: - Whether you install your stove yourself or hire a professional installer, a quality installation is a must for the safety of your family as well as efficient, satisfactory operation. - Initial setup of the stove is the most important step to ensure consistent, comfortable operation. - Know the quality and characteristics of the pellets you burn. Pellets can vary greatly from company to company, from load to load and even from bag to bag. - Be dilligent in your cleaning program. - Remember that most operational dilemmas with pellet stoves arise from improper installation, poor quality pellets, lack of timely cleaning or incorrect air flow adjustment. With a minimum amount of consistent care, your pellet appliance will provide years of clean, efficient, comfortable and environmentally sound heating. Dear Pellet Appliance Owner, FOREWORD TO NEW OWNERS Congratulations on the purchase of your wood pellet appliance. You have selected the finest in residential wood pellet heating technology. This OPERATIONS GUIDE will walk you through the initial setup of your pellet stove, from first light to fine tuned adjustments. We have also included detailed information on cleaning and maintenance as well as wood pellet fuel facts. Please note the following points regarding stove installation and pellet heating in general: - Whether you install your stove yourself or hire a professional installer, a quality installation is a must for the safety of your family as well as efficient, satisfactory operation. - Initial setup of the stove is the most important step to ensure consistent, comfortable operation. - Know the quality and characteristics of the pellets you burn. Pellets can vary greatly from company to company, from load to load and even from bag to bag. - Be dilligent in your cleaning program. - Remember that most operational dilemmas with pellet stoves arise from improper installation, poor quality pellets, lack of timely cleaning or incorrect air flow adjustment. With a minimum amount of consistent care, your pellet appliance will provide years of clean, efficient, comfortable and environmentally sound heating. UPDATES Updated manuals, product registration and warranty information can be found on our website: Thank you for selecting our wood pellet stove! Sincerely, Dansons Group Inc. and Canadian Comfort Industries We do NOT recommend pellet stoves as your only source of heat. Do NOT install in a sleeping room. Use of outside air is highly recommended with our pellet stoves, heaters and inserts. Do not operate with the front door or hopper lid open. Keep children, furniture, fixtures and all combustibles away from any heating appliance. Installation and use of a carbon monoxide detector is highly recommended. LIGHTING PROCEDURE STARTUP CHECKLIST 2ABCD1The COMBUSTION FAN (exhaust) will start and operate at full speed for 60 seconds, then will slow to match the startup rate Please make certain you have completed the following checklist before proceeding: Unit is plugged into a 3 pronged grounded outlet Burn pot is clean, level & seated properly Front door of the stove is closed Screened pellets are in the hopper Pellet fuel complies with PFI standards (pelletheat.org) Unit is NOT plugged into a GFI outlet (ground fault interruptor) . . . . . . . . . . Used only PL or L approved venting Sealed vent connections with high temp RTV sealant and allow sealant to cure for 24 hours Make sure #1 trim pod is set to 9 o’clock positionAir inlet damper is OPEN to between 1/4” and 1/2” STARTING UP YOUR PELLET STOVE We STRONGLY recommend the use of a surge protector to protect the circuitry in your control board. (see ‘Initial Setup’ section on page 4) (see pg 5) FOR NEW INSTALLATIONS: Push firmly on the START / FEED RATE button. Procedures listed will work with both AcuTron II & AcuTron III control boards. The CONVECTION FAN (heat circulation) will start and the LED will go solid on LOW setting The AUGER CYCLE LED will go solid for 3 seconds indicating the signal is being sent to auger motor The IGNITER LED will light up solid and the igniter will begin to heat up LIGHTING PROCEDURE STARTUP CHECKLIST 2ABCD1The COMBUSTION FAN (exhaust) will start and operate at full speed for 60 seconds, then will slow to match the startup rate Please make certain you have completed the following checklist before proceeding: Unit is plugged into a 3 pronged grounded outlet Burn pot is clean, level & seated properly Front door of the stove is closed Screened pellets are in the hopper Pellet fuel complies with PFI standards (pellet...