Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
Kitchen-ranges - PRD364GDHC/15 (4.56 mb)
Kitchen-ranges - PRD364GDHC/15 (6.17 mb)
manual abstract
Call THERMADOR® Customer Care Center at 1-800-735-4328 or your nearest THERMADOR dealer to determine the proper replacement bulb for your range. You will need to know your range’s model number and serial number. To Replace the Light Bulb: For bulb replacement, any commercially available bulb with the following specification can be used: 120 or 130 VAC, 50 W max., G8 base, Halogen. Use a clean, dry cloth to handle halogen light bulbs. This will increase the life of the bulb. LensHalogenLampHousingCeramicHolderHolderClip 1. Turn off circuit breaker. 2. Remove oven racks. 3. Slide the tip of a flat blade screw driver between the fixing clip and the lamp housing (Figure 32, A). A. B. C. D. Figure 32: Bulb Replacement 4. Support the glass lens cover with two fingers along the bottom edge to prevent the cover from falling to the bottom of the oven. Gently twist the flat blade screw driver to loosen the glass lens cover. 5. Remove the glass lens cover and fixing clip. 6. Remove the bulb by grasping and sliding the bulb straight back until the two prongs have cleared the ceramic holder (Figure 32, B). 7. Do not touch the glass of the new replacement bulb with your fingers. It may cause the bulb to fail when it first lights. Grasp the replacement bulb with a clean dry cloth. Locate the two prongs in the ceramic holder, gently poking until the two prongs locate in the ceramic socket. 8. Press down to seat the bulb (Figure 32, C). 9. Slide the protective lens into the holder clip and push the other end until the fixing clip snaps back into the housing (Figure 32, D). 10. Turn on circuit breaker. Figure 31: Oven Lamp Assembly English 35 Power Failure In the event of a power failure, only the standard STAR® burners can be lit manually. It is necessary to light each standard burner individually (see also page 15). If the range's cooktop is being used when the power failure occurs, turn all of the burner control knobs to the OFF position. The standard burners can be lit by holding a match at the ports and turning the control knob to the HI position. Wait until the flame is burning all the way around the burner cap before adjusting the flame to the desired height. Intermittent or Constant Igniter Sparking The two ExtraLow® burners on the left sides cannot be used during a power failure. Be sure to turn them OFF if a power failure occurs because they will not turn back on until the control knobs are turned OFF and then turned back on again. If you have low gas pressure, contact your gas company. Intermittent or constant sparking of the sealed gas surface burners can result from a number of preventable conditions. Eliminate these conditions as indicated in the following chart. SYMPTOM CAUSE REMEDY Intermittent sparking • Ceramic igniter is wet or dirty. • STAR burner ports are clogged. • Carefully dry or clean igniter. • Clean ports on STAR burner cap with a wire, a needle or straightened paper clip. More than four clicks of igniter before lighting • Improper fit of STAR burner cap onto STAR burner base. • Align STAR burner cap properly on STAR burner base. Constant Sparking • Range is not properly grounded. • Electrical power supply is incorrectly polarized. • Refer to the Installation Manual. Have a qualified electrician ground the range properly. • Refer to the Installation Manual. Have a qualified electrician ground the range properly. English 36 English 37 Before Calling For Service Before calling for service, check the following to avoid unnecessary service charges. Be sure to check these items first: • Is there a power outage in the area? • Is the household fuse blown or the circuit breaker tripped? • Is the range disconnected from the electrical supply? If the burners do not ignite: • Are the burner caps properly aligned and seated in the burner bases? • Are the burner ports clogged? • Is a fuse blown or is the circuit breaker tripped? • Is the manual shut-off valve closed, preventing the flow of gas? Data Rating Label The data rating plate shows the model and serial number of your range. It is located on the frame, behind the oven door (Figure 33). The electric wiring diagrams and schematics are attached behind the toe kick, and should not be removed except by a service technician, then replaced after service (Figure 33). Service Information For handy reference, copy the information below from the data rating plate located on the frame, behind the oven door. Keep your invoice for Warranty validation. Model Number __________________________________ Serial Number ___________________________________ Date of Purchase ________________________________ Dealer’s Name __________________________________ Dealer’s Phone Number ___________________________ Service Center's Name ____________________________ Service Center’s Phone Number ____________________ Also, enter this information on the Product Registration Form included with this product, then mail it to the indicated address. Register your BSH product to ensure timely serv...
Other models in this manual:Kitchen-ranges - PRD366GHC/13 (2.79 mb)