Votes - 0, Average rating: 0
(
)
)
|
manual abstract
The burner cup and ¶burner cap must be positioned exactly. ¦ Ensure that the top cover is not closed when the oven is started up. Damage to the oven Caution! ¦ Do not push baking trays onto the oven floor. Do not line the oven floor with aluminium foil. Do not place any food containers on the oven floor, as this could cause heat to accumulate. The baking and roasting times will no longer be correct and the enamel will be damaged. ¦ Do not pour water directly into a hot oven. This could damage the enamel. ¦ Do not use too much fruit when baking a very liquid fruit cake. Fruit juice, which drips from the baking tray, may cause stains that cannot be removed. ¦ Do not use the open oven door as a seat or footstool. Damage to the plinth drawer Caution! Do not place hot objects in the plinth drawer. It could be damaged. Damage to the fronts of adjacent units Caution! ¦ Only allow the oven to cool down with the oven door closed. Even if the door is only open slightly open, the fronts of adjacent units could be damaged over time. ¦ If the oven seal is very dirty, the oven door will not close properly during operation. The fronts of adjacent units will become damaged over time. Always keep the door seal clean. Set-up, gas and electricity connection Gas connection Installation must only be performed by an approved expert or a licensed after- sales service engineer in accordance with the instructions specified under " Gas connection and conversion to a different gas type" . For the licensed expert or after- sales service Caution! ¦ The setting conditions for this appliance are specified on the rating plate on the back of the appliance. The gas type set in the factory is marked with an asterisk ( * ) . ¦ Before setting up the appliance, check the grid access conditions ( gas type and gas pressure) and ensure that the gas setting of the appliance meets these conditions. If the appliance settings have to be changed, follow the instructions in the section "Gas connection and conversion to a different gas type" . ¦ This appliance is not connected to a waste gas main. It must be connected and commissioned in accordance with the installation conditions. Do not connect the appliance to a waste gas main. All ventilation regulations must be observed. ¦ The gas connection must be made via a fixed, i. e. not mobile connection (gas line) or via a safety hose. ¦ If using the safety hose, ensure that the hose is not trapped or crushed. The hose must not come into contact with hot surfaces. ¦ The gas line ( gas pipe or safety hose) can be connected to the right or left-hand side of the appliance. The connection must have an easily accessible locking device. Faults in the gas installation/smell of gas If you notice a smell of gas or faults in the gas installation, you must ¦ immediately shut off the gas supply and/ or close the gas cylinder valve ¦ immediately extinguish all naked flames and cigarettes ¦ switch off electrical appliances and lights ¦ open windows and ventilate the room ¦ call the aftersales service or the gas supplier Electrical connection Caution! ¦ Have the appliance set up by your after- sales service. A 16 A fuse is required for connection. The appliance is designed for operation at 220-240 V. ¦ If the electricity supply drops below 180 V, the electrical ignition system does not work. ¦ Any damage arising from the appliance being connected incorrectly will invalidate the guarantee. For the after- sales service Caution! ¦ The appliance must be connected in accordance with the data on the rating plate. ¦ Only connect the appliance to an electrical connection that meets the applicable provisions. The socket must be easily accessible so that you can disconnect the appliance from the electricity supply if necessary. ¦ Please ensure the availability of a multi- pin disconnecting system. ¦ Never use extension cables or multiple plugs. ¦ For safety reasons, this appliance must only be connected to an earthed connection. If the safety earth terminal does not comply with regulations, safety against electrical hazards is not guaranteed. ¦ You must use a H 05 W-F type cable or equivalent for the appliance connection. Levelling the cooker Always place the cooker directly on the floor. 1. Pull out the plinth drawer and lift it up and out. There are adjustable feet at the front and rear on the inside of the plinth. 2. Use an Allen key to raise or lower the adjustable feet as necessary until the cooker is level ( picture A) . 3. Push the plinth drawer back in ( picture B) . Setting up the appliance ¦ The appliance must be set up directly on the kitchen floor and in line with the specified dimensions. The appliance must not be set up on any other object. ¦ The distance between the top edge of the oven and the bottom edge of the extractor hood must meet the requirements of the extractor hood manufacturer. ¦ Ensure that the appliance is not moved again after set up. The distance from the high output burner or wok burner to the fron...