3. While the burner is alight, quickly change the position of the knob from minimum to maximum and vice versa several times, checking that the flame is not extinguished. ! The hob burners do not require primary air adjustment. Adapting the oven Replacing the oven burner nozzle: 1. Remove the oven compartment. 2. Slide out the protection panel A (see diagram). A V 3. Remove the oven burner after unscrewing the screws V (see figure). The whole operation will be made easier if the oven door is removed. 4. Unscrew the nozzle using a special nozzle socket spanner (see figure) or with a 7 mm socket spanner, and replace it with a new nozzle that is suited to the new type of gas (see Burner and nozzle specifications table). Adjusting the gas oven burner.s minimum setting: 1. Light the burner (see Start-up and Use). 2. Turn the knob to the minimum position (MIN) after it has been in the maximum position (MAX) for approximately 10 minutes. 3. Remove the knob. 4. Tighten or loosen the adjustment screws on the outside of the thermostat pin (see figure) until the flame is small but steady. ! If the appliance is connected to liquid gas, the adjustment screw must be fastened as tightly as possible. GB 15 GB GB 5. Turn the knob from the MAX position to the MIN position quickly or open and shut the oven door, making sure that the burner is not extinguished. TECHNICAL DATA Oven dimensions (HxWxD) 34x39x44 cm Volume 58 l Useful measurements relating to the oven compartment width 42 cm depth 44 cm height 18 cm Power supply voltage and frequency see data plate Burners may be adapted for use with any type of gas shown on the data plate, which is located inside the flap or, after the oven compartment has been opened, on the left-hand wall inside the oven. EC Directives: 2006/95/EC dated 12/12/06 (Low Voltage) and subsequent amendments 2004/108/EC dated 15/12/04 (Electromagnetic Compatibility) and subsequent amendments 2009/142/EC dated 30/11/09 (Gas) and subsequent amendments - 93/68/EEC dated 22/07/93 and subsequent amendments - 2002/96/EC. 1275/2008 (Stand-by/ Off mode) Table of burner and nozzle specifications !"" # $ !"" # !"" # ! %&& # '$% ( ) + 2) 62 6+ 62 62: +( 62: ; # <& ; )> ? + ( ) (2 (: + 2 2 2 @D ; @ > + ( >6 )( ) ): ?> 2 ?> EF 6 +2+? :2 +> +( ) ? + ? ; ! G < G () 6> +> 6 ) 6> ( :H> 2 * At 15°C and 1013 mbar- dry gas ** Propane P.C.S. = 50,37 MJ/Kg *** Butane P.C.S. = 49,47 MJ/Kg Natural P.C.S. = 37,78 MJ/m3 S S RA KJ3G2/R 16 Descriptionof the appliance Overall view Gas burner Containment surface for spills Hob grid GUIDE RAILS Control panel for the sliding racks position 5 GRILL position 4 position 3 DRIPPING PAN position 2 position 1 Adjustable foot Adjustable foot GB Control panel Oven Control Knob Control Knobs for Gas Burners on Hob 17 Start-up and use GB Using the hob Lighting the burners For each BURNER knob there is a complete ring showing the strength of the flame for the relevant burner. To light one of the burners on the hob: 1. Bring a flame or gas lighter close to the burner. 2. Press the BURNER knob and turn it in an anticlockwise direction so that it is pointing to the maximum flame setting E. 3. Adjust the intensity of the flame to the desired level by turning the BURNER knob in an anticlockwise direction. This may be the minimum setting C, the maximum setting Eor any position in between the two. Practical advice on using the burners For the burners to work in the most efficient way possible and to save on the amount of gas consumed, it is recommended that only pans that have a lid and a flat base are used. They should also be suited to the size of the burner. . . . . . . . . To identify the type of burner, please refer to the diagrams contained in the .Burner and nozzle specifications.. Using the oven ! The first time you use your appliance, heat the empty oven with its door closed at its maximum temperature for at least half an hour. Ensure that the room is well ventilated before switching the oven off and opening the oven door. The appliance may emit a slightly unpleasant odour caused by protective substances used during the manufacturing process burning away. ! Before operating the product, remove all plastic film from the sides of the appliance. ! Never put objects directly on the bottom of the oven; this will avoid the enamel coating being damaged. Only use position 1 in the oven when cooking with the rotisserie spit. Lighting the oven F To light the oven burner, apply a lighted match or a lighter to hole and while pressing in all the way set the oven knob on maximum maximummaximummaximummaximummaximum E EEEEE. The burner can be used at maximum or intermediate settings. These settings, maximum maximummaximummaximummaximummaximum E EEEEE. and minimum minimumminimumminimumminimumminimum C CCCCCare indicated on the knob, plus off, identified by the symbol . and operative when this symbol points to the notch. For the min...
)
