Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
560 mm. 45 mm. Centring and fastenin. Secure the appliance to the cabinet by opening th. oven door and fastening 4 screws into the 4 holes o. the outer frame. ! All parts ensuring the safe operation of the applianc. must not be removable without the aid of a tool. Electrical connection. ! Ovens equipped with a three-pole power suppl. cable are designed to operate with alternating curren. at the voltage and frequency indicated on the dat. plate located on the appliance (see below). Fitting the power supply cabl. N L 1. Open the terminal board b. inserting a screwdriver into th. side tabs of the cover. Use th. screwdriver as a lever b. pushing it down to open th. cover (see diagram). 2. Install the power suppl. cable by loosening the cabl. clamp screw and the three wir. contact screws L-N. Connect the wires to th. corresponding terminals. adhering to the colour code o. Blue (N), Brown (L) and Yellow. Green. (see diagram). 3. Secure the cable by fastening the clamp screw. 4. Close the cover of the terminal board. Connecting the supply cable to the main. Install a standardised plug corresponding to the loa. indicated on the data plate (see adjacent box). The appliance must be directly connected to th. mains using an omnipolar circuit-breaker with . minimum contact opening of 3 mm installed betwee. the appliance and the mains. The circuit-breake. must be suitable for the charge indicated and mus. comply with current electrical regulations (the earthin. wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact wit. surfaces with temperatures higher than 50°C. ! The installer must ensure that the correct electrica. connection has been made and that it is complian. with safety regulations. Before connecting to the power supply, make sure that. . the appliance is earthed and the plug is complian. with the law. . the socket can withstand the maximum power of th. appliance, which is indicated on the data plate (se. below). . the voltage is in the range between the value. indicated on the data plate (see below). . the socket is compatible with the plug of th. appliance. If the socket is incompatible with th. plug, ask an authorised technician to replace it. D. not use extension cords or multiple sockets. ! Once the appliance has been installed, the powe. supply cable and the electrical socket must be easil. accessible. ! The cable must not be bent or compressed. ! The cable must be checked regularly and replace. by authorised technicians only (see Assistance). ! The manufacturer declines any liability should these safety measures not be observed. Gas connectio. The appliance should be connected to the main ga. supply or to a gas cylinder in compliance with curren. National regulations. Before carrying out th. connection, make sure the cooker is compatible wit. the gas supply you wish to use. If this is not the case. follow the instructions indicated in the paragrap. .Adapting to different types of gas.. When using liquid gas from a cylinder, install . pressure regulator that complies with current Nationa. regulations. GB GBGB ! Check that the pressure of the gas supply i. consistent with the values indicated in Table . (.Burner and nozzle specifications.) since this wil. ensure the safe operation and longevity of you. appliance while maintaining efficient energ. consumption. ! Should you need to install a gas hob on top of . built-in gas oven, it is strictly forbidden to connect th. two or to use a single cut-off tap. The two appliance. should be connected separately, and each on. should have its own stop tap in order to make the. completely independent from one another (se. figures). NO OK Connection with a rigid pipe (copper or steel. ! Connection to the gas system must be carried out i. such a way as not to place any strain of any kind o. the appliance. There is an adjustable L-shaped pipe fitting on th. appliance supply ramp and this is fitted with a seal i. order to prevent leaks. The seal must always b. replaced after rotating the pipe fitting (the seal i. provided with the appliance). The gas supply pipe fittin. is a threaded 1/2 gas cylindrical male attachment. Connecting a flexible jointless stainless steel pip. to a threaded attachmen. The gas supply pipe fitting is a threaded 1/2 ga. cylindrical male attachment. These pipes must be installed so that they are neve. longer than 2000 mm when fully extended. Onc. connection has been carried out, make sure that th. flexible metal pipe does not touch any moving part. and is not compressed. ! Only use pipes and seals that comply with curren. National regulations. Checking the tightness of the connectio. ! When installation has been completed, check th. pipe fittings for leaks using a soapy solution. Neve. use a flame. Adapting to different types of ga. In order to adapt the oven to a type of gas other tha. the type for which it was manufactured (indicated o. the label), follow these simple steps. . Replacing the oven burner n...