Votes - , Average rating:
(
)
)
Manafacture: Vitek
File size: 643.57 kb
File name: Vitek-VT-3773-Pdf-Rus.Pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
If the display is blank - no number show when Play/Pause button (6) is pressed, the batteries are dead. Replace them or use AC adapter (Also, check if you inserted the batteries according to the + and - as shown on set). IMPORTANT NOTE: Spent or discharged batteries must be recycled or disposed of properly in compliance with all applicable laws. For detailed information, contact your local dealer. POWER SOURCES CHARGING AND USE OF RECHARGEABLE BATTERIES This unit can fully recharge the specified rechargeable batteries, in approximately 15 hours. The rechargeable batteries (NOT supplied) should be recharged before they are used for the first time because they are low in power or they have not been used for a long period (over 60 days). 1. Open the battery compartment cover and insert two of the recommended rechargeable batteries (1,2 V 650 mA), matching polarity. ALL BATTERIES MUST BE OF RECHARGEABLE MICKEL-CADMIUM TYPE. OTHER WISE THE BATTERIES MAY EXPLODE OR LEAK. DURING CHARGING, THE CHARGE INDICATOR (19) KEEPS ON. 2. Plug in the AC adaptor and set the Charge switch (20) to the ON position to start charging. 3. After 15 hours, please unplug the AC adapter and the Charge switch (20) must be set to the OFF position. DO NOT CHARGE CONTINUOUSLY FOR 24 HOURS OR MORE. DOING SO CAN CAUSE THE PERFOMANCE OF THE RECHARGEABLE BATTERIES TO DETERIORATE. NOTE: you may play DISC whilst charging the batteries. 4. If the operating time decreases drastically even when the rechargeable nickel- cadmium batteries are properly recharged, purchase a new set of rechargeable nickel-cadmium batteries. 5. When charging for the first time or after a long time, playing time may be reduced. In this case, charge and discharge the batteries several times. HANDLING COMPACT DISCS This unit is designed to play compact bearing the identification logo. Discs that do not carry this logo may not conform to the CD standard and may not play properly. Dirty scratched or warped discs may cause skipping or noise. Pay attention to the following: Handle the disc only by the edges. To keep the disc clean, do not touch the surface of the disc. 1. Discs should be returned to their case after use to avoid serious scratches that could cause the laser pickup to skip. 2. Do not expose disc to direct sunlight, high humidity, or high temperatures for extended periods. Prolonged exposure to high temperatures can warp the disc. i 5 3773.qxd 10.06.03 17:33 Page 12 ENGLISH 3. Do not apply paper or write anything on either side of the compact disc. Sharp writing instruments, or the inks used in some felt-tip pens, may damage the surface of the disc. DISC PLAYING Be sure to reduce the volume before plugging in or unplugging the headphones/earphones. 1. Plug the cord from a pair of earphones into the PHONES jack (13). Cautions: Listening at high power for a long moment could damage users'ears. 2. Slide the CD DOOR OPEN switch (15) to open the CD door. 3. Hold the disc with the label side up and press it onto the spindle until it “clicks” into place. 4. Close the disc compartment, press PLAY/PAUSE button (6), the disc will begin to spin, the display will indicate “READ” and then the total number of tracks and total playing time will appear on the display. Play will begin from track number 1 automatically. READING V CD 0 14 64:51 & CD 00 1 00:01 PLAY 5. Adjust the volume as desired. 6. Set the following functions as desired. 7. To stop playing temporarily, press the PLAY/PAUSE button (6). The elapsed playing time flashes in the display. Press the PLAY/PAUSE button (6) again to resume. 9. To stop playing, press the STOP/OFF button (7). Total tracks and total playing time appears in the display. Press the STOP/OFF button (7) once again, power will turn off immediately. AUTO POWER ON FUNCTION • The power turns on automatically when the PLAY/PAUSE button (6) is pressed. AUTO POWER OFF FUNCTION • The power turns off automatically when all tracks on a disc have been played or after 30 seconds when the STOP/OFF button (7) is pressed once during playback. Open the disc compartment also turns off the power. CD 00 1 -00:44-PAUSE " " 1 " CD 0 14 64:51 STOP 6 РУССКИЙ 3. Нажмите кнопку PROG/EQ (8), при этом на дисплее появится номер трека “ООО”. 4. Для выбора 3-го трека воспользуйтесь кнопками SKIP/SEARCH шДи (2, 5), при этом на дисплее появится “003”. 5. Снова нажмите кнопку PROG/EQ (8), при этом на дисплее появится “Р-02” - вы можете программировать следующие треки. 6. Для программирования других треков, повторите шаги 3-5. 7. Для начала запрограммированного воспроизведения нажмите кнопку "PLAY/PAUSE" (6). ПРОИГРЫВАНИЕ В РЕЖИМЕ “INTRO” 1. В режиме воспроизведения нажмите кнопку MODE (4) четыре раза, при этом на дисплее появится индикатор “INTRO”. 2. Нажмите на кнопку "PI_AY/PAUSE" (6) для сканированного воспроизведения треков МРЗ-диска. ВОСПРОИЗВЕДЕНИЕ ДОРОЖЕК В ПРОИЗВОЛЬНОМ ПОРЯДКЕ Каталоги и треки МРЗ-диска...