Votes - 0, Average rating: 0
(
)
)
|
manual abstract
when you were jogging. The ELECTRONIC SKIP PROTECTION prevents loss of sound caused by light vibrations and shocks. Continuous playback is ensured. However ESP does not prevent playback interruptions during vigorous running. It also does not protect the unit against any damage caused by dropping! On this set ESP is default on. It is possible to set ESP off and enter the Power Save mode. The Power Save mode helps to extend battery lifetime for longer playback. • Press MODE for more than 2 seconds. y disappears. power save modeis now activated. • Press MODE again for more than 2 seconds. y is displayed once RESUME and HOLD You can interrupt playback and continue (even after an extended period of time) from the position where playback stopped (RESUME) and you can lock all buttons of the set so that no action will be executed (HOLD). Use the RESUME–HOLD–OFF slider for these functions. RESUME – continuing from where you have stopped 1 Switch the slider to RESUME during playback to activate RESUME. yresume is shown. 2 Press 9 whenever you want to stop playback. 3 Press 2; whenever you want to resume playback. yresume is shown and playback continues from where you have stopped. • To deactivate RESUME, switch the slider to OFF. yresume goes off. HOLD – locking all buttons You can lock the buttons of the set by switching the slider to HOLD. Now, when a key is pressed, no action will be executed. This is of use, for example, when transporting the player in a bag. With HOLD activated, you can avoid accidental activation of other functions. 1 Switch the slider to HOLD to activate HOLD. yAll buttons are locked. HoLd is shown when you press any button. If the set is switched off, hold will be shown only when 2; or FM is pressed. 2 To deactivate HOLD, switch the slider to OFF. Note: If you deactivate HOLD by switching the slider to RESUME, you will be activating the RESUME function. FEATURES Radio Play You can tune to any FM station automatically or manually. 1 Press FM to switch the radio on. Tuning to radio stations automatically 1 Keep . or § pressed for at least 2 second. yThe radio tunes to a station with sufficient strength and radio play starts. The current waveband and frequency are displayed. 2 Repeat searching until you find the desired radio station. Tuning to radio stations manually 1 Keep . or § pressed. 2 Release . or §, then briefly press . or § again when you are close to the desired frequency. 3 Briefly press . or § repeatedly until you reach the desired frequency. yRadio play starts. The current waveband and frequency are displayed. • To switch from radio play to CD play, press 2; . • Press FM or 9 to switch the radio off. Antennas The headphone wire is used as an FM antenna. If necessary, move it for optimum reception. Storing radio stations You can store up to 30 radio stations (1-30). 1 Tune to a desired radio station and press PROG. 2 Press PRESET3 ,4 repeatedly if necessary to select the number that should be assigned to this radio station. 3 Press PROG while PRESET is blinking to confirm the storage. yPRESET, the waveband, the frequency and the preset number of the stored station are displayed. 4 Store all desired stations this way. Note: Already stored stations can be recognized by the indicator PRESET and the preset number. Tuning to a stored radio station 1 Press FM to switch the radio on. 2 Press PRESET3 ,4 once or more to find your preset station. yRadio play starts. program, the waveband, the frequency and the preset number of the stored station are displayed. TROUBLESHOOTING Troubleshooting WARNING: Under no circumstances should you try to repair the set yourself as this will invalidate the guarantee. If a fault occurs, first check the points listed, before taking the unit for repair. If you are unable to solve a problem by following these hints, consult your dealer or service centre. The CD player has no power, or playback does not start • Check that your batteries are not dead or empty, that they are inserted correctly, that the contact pins are clean. • Your adapter connection may be loose. Connect it securely. • For in-car use, check that the car ignition is on. Also check player’s batteries. The indication no diSC is displayed • Check that the CD is clean and correctly inserted (label-side upward). • If your lens has steamed up, wait a few minutes for this to clear. The indication nF diSC is displayed • CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder. The indication HOLD is on and/or there is no reaction to controls • If HOLD is activated, then deactivate it. • Electrostatic discharge. Disconnect power or remove batteries for a few seconds. The CD skips tracks • The CD is damaged or dirty. Replace or clean the CD. • RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on. Troubleshooting No sound or bad sound quality. • PAUSE might be active. Press 2;. • Loose, wrong or dirty connections. Check and clean connections. • Volume might not be appropriately ...