Votes - 2, Average rating: 4
(
)
)
|
Photos and specs Hyundai H-CD7002 |
manual abstract
Please connect AC adaptor with the Player and then put AC adaptor in AC socket to use AC adaptor. The output power and polarity of the AC adaptor is shown as below: Output: 4.5V DC, 600mA Positive rt>- — Negative Note: • If batteries and AC adaptor are both used, the player will be powered by AC adaptor and not by battery automatically. 7 Illustration of player’s operation 1. LCD 2. PLAY button 3. PAUSE button 4. NEXT/FF button 5. VOL+/VOL- 6. AUDIO/VIDEO jack 7. Phone jack . ~ 8. Remote jack for wired control with LCD 9. EQ button 10. Open switch 11. MODE button \ \ — 12. R/L 13. PREV/FB button 14. ESP button 15. STOP button Wired control Introducing the buttons and jacks of the wired control: 1. PREV 2. ESP 3. NEXT 4. LCD 5. STOP 6. VOL - 7. PLAY/PAUSE 8. EARPHONE JACK 9. VOL + 10. HOLD Note: The operations of the buttons on Wired control are as same as buttons on Panel of the unit. 9 Introduction of LCD 1. CD: Appears the when playing disc is CD. 2. VCD: appears when the playing disc is VCD. 3. MP3: appears when the playing disc is MP3. 4. REP: indicates the repeat mode (repeat one or repeat all). 5. PROG: Appears when play disc in program. 6. Indicates the capacity of the batteries. 7. Indicates the playing track or directory. 6 7 8 9 Note: • When the folder has over 100 songs, the information on the LCD is as follows (this example is for the first folder on the CD): Number of song Information on LCD (XX - the figures in the track number) 1 - 99 1XX 100-109 1aX 110-119 1bX 10 120-129 1cX 130-139 1dX 140-149 1eX 150-159 1fX 160-169 1GX 170-179 1HX 180-189 1IX 190-199 1JX 200-209 1KX 210-219 1LX 220-229 1MX Etc. 8. Indicates the track’s playing time (minute: second). 9. Indicates the status of anti-shock. 11 How to operate 1. Play/pause Press the button and the unit will begin to play the disk. Pressing it again will pause the playing. Note: • To power on the device press the PLAY button on the unit. The PLAY button on the wired control cannot power on the device. 2. Stop Pressing the button will stop the playing and press it again to turn the power off (at charge off state). 3. Prev/next Play the previous song by pressing “PREV” button and the next song by pressing “NEXT” button. 4. Directory select When playing MP3, keep pressing “ESP” button for 3 seconds to get into directory selection mode, the playing directory is flashing on LCD. You can select desired directory by pressing “PREV” or “NEXT” button, and the player will play the first song of the selected directory automatically. 12 5. FF/FB Playing CD or VCD, keep pressing “PREV” or NEXT” button for reading the disc fast backward or fast forward, and release the button for normal playing. 6. Repeat playing At playing state, press the “MODE” button to switch “REPEAT ONE”, “REPEAT ALL” and “CANCEL REPEAT”. 7. Hold switch Slide the HOLD Switch to “ON” position and all the buttons on the unit are disabled, this may avoid influence by mistaking pressing buttons. 8. Anti-shock When playing CD, press “ESP” button to turn on anti-shock, press it again to turn off. When playing MP3, anti-shock is turning on automatically and cannot be turn off. 9. How to select playing mode • Random Playing Mode At stop state (with power on), press “MODE” button one time, then press “PLAY/PAUSE” button and the unit will play songs in random. 13 • Intro Playing Mode At stop state (with power on), press “MODE” button two times, then press “PLAY/PAUSE” button and unit will play in INTRO mode: play every song’s first 10 seconds (In MP3 playing, this function is disable). At this time press “ PLAY/PAUSE” button again to resume normal playing. • Programmed Playing Mode At stop state (with power on), press “MODE” button three times and the unit enter “PROG PLAYING MODE”. Select songs you are going to play by pressing “PREV” or “NEXT” button, press “MODE” button to confirm, after all songs that you want to play have been selected, press “PLAY/PAUSE” button to start PROG playing. If Playing VCD, you can select songs by pressing digital keys on Remote control, then press “PLAY/PAUSE” button for begin to play in PROG (Note: When playing MP3, press “ESP” button to turn over to the next table of content for PROG playing). • Video System Select When Playing VCD, press “ESP” button for 3 seconds to switch video system: PAL--»NTSC. • Audio Mode Select Pressing the EQ button repeatedly will cycle the unit through the following mode: STANDARD^ CLASSICALITY^ROCK AND ROLL^JAZZ^POPULARITY^STANDARD, it is corresponding to “EQ off” to “EQ4” showing on LCD (At CD Playing with anti-shock on, the audio mode is disable). • Video Output On/Off 14 When Playing VCD with batteries, video output is shut off automatically. Keeping pressing “EQ” button for 3 seconds to turn the video output on. 10. Volume control Press “VOL+” or “VOL-” button to control volume. 11. Audio output select Press “R/L” butto...