Votes - , Average rating:
(
)
)
Manafacture: Memorex
File size: 182.67 kb
File name: 531cc490-b2a6-4586-b600-8a6379e20556.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
14. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 4 SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE 15. OVERLOADING Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 16. OBJECT AND LIQUID ENTRY Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product. 17. OUTDOOR ANTENNA GROUNDING If an outside antenna is connected to the product, be sure the antenna system is grounded so as to provide some protection against voltage surges and built- up static charges. Section 810 of the National Electric Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge product, size of grounding conductors, location of antenna discharge product, connection to grounding electrodes and requirements for grounding electrodes. 18. SERVICING Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 19. REPLACEMENT PARTS When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 20. SAFETY CHECK Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 21. WALL OR CEILING MOUNTING The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 22. DAMAGE REQUIRING SERVICE Unplug the product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been damaged. f. When the product exhibits a distinct change in performance–this indicates a need for service. 23. HEAT The product should be situated away from heat sources such as radiators, heat registers, stoves or other products (including amplifiers) that produce heat. 24. NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 5 LOCATION OF CONTROLS LOCATION OF CONTROLS 431172131210115678918191416201521 1. Carrying Handle 2. CD Compartment 3. PHONES (Headphones) Jack (Top of Unit) 4. VOLUME Control 5. CD Door Open/Close Area 6. PLAY/PAUSE (®p)/CD Button 7. PRESET DOWN †/RANDOM Button 8. POWER Button 9. STOP (n) Button 10. Display 11. EQ Button 12. FM MODE Button 13. Left Speaker 14. FM Antenna 15. AC Power Jack (Rear of Unit) 16. TUNE/SKIP/SEARCH o/n Control 17. PRESET UP ./REPEAT Button 18. TUNER/BAND Button 19. PROGRAM Button 20. Right Speaker 21. Battery Compartment (Bottom of Unit) 6 POWER SOURCES POWER SOURCES This unit is designed to operate on AC household current or DC (batteries). AC Use the AC polarized line cord included with the unit for operation on AC power. Insert one end of the AC line cord into the AC power jack on the rear of the unit and the other end (with the 2 blades) into a conveniently located AC outlet having 120V, 60Hz. When the AC cord is plugged in, the batteries will be disconnected. NOTE: The AC plug supplied with the unit is polarized to help minimize the possibility of electric shock. If the AC plug does not fit into a nonpolar AC PlugAC Outlet ized AC outlet, do not file or cut the wide blade. It is the user’s responsibility to have an electrician replace the obsolete outlet. BATTERY INSTALLATION To use this unit with battery power, remove the battery door on the bottom of the unit by pressing in on the two tabs, then lifting the...