Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
26) EFFECT ON/OFF Switch This switch turns the effector and voice change on and off. When this switch is ON, the display shows EFFECT. TASCAM CD-VT1MKII — 11 Making connections Connecting a microphone (MIC IN 1 / MIC IN 2) MICROPHONES . Connect a microphone to either the MIC IN 1 jack or the MIC IN 2 jack. You can also connect microphones to both jacks and use them together. . The MIC IN jacks (1 and 2) of the CD-VT1MKII accept unbalanced input signals. Use a . inch mono phone plug. Adjusting the microphone level Use the INPUT control to adjust the level of the input signal from the MIC IN 1 and MIC IN 2 jacks. . The INPUT control adjusts the input level of MIC IN 1 jack and MIC IN 2 jack together (the levels of the two jacks cannot be adjusted separately). Adjusting the mix balance between microphone(s) and CD Press and hold down the CD EFF/ SETUP key to open the Setup menu, and press either the NEXT or PREV key to choose MIX. You can set the mix balance using values between M (Mic) 10 – M1, 0, C (CD) 1 – C10. Inputting signals from external devices (LINE IN) LINE OUT OF EXTERNAL DEVICE . The LINE IN jack accepts a stereo mini-jack plug (3.5mm). . The input level at the LINE IN jack cannot be adjusted, so adjust the output level on the external device you have connected. 12 — TASCAM CD-VT1MKII Making connections (Continued) Output to headphones and external devices . Connect headphones to the PHONES jack. . Use the stereo LINE OUT jack to connect the CD-VT1MKII to external devices, such as speakers with a built-in amplifier, AUX input jacks of a stereo system, cassette tape recorders, or CD recorders. Adjusting the output level You can adjust the output level of LINE OUT and PHONES by using the OUTPUT control. NOTE The levels from both the LINE OUT and PHONES jacks are controlled together by the OUTPUT control and cannot be adjusted independently. When you have a recording device connected to the LINE OUT jack, remember that the OUTPUT control affects the recording level. NOTE When you are using the CD-VT1MKII with speakers and microphone(s), be careful to avoid feedback (howlround). TASCAM CD-VT1MKII — 13 Using the menu system Entering the menu system To enter the menu category of your choice, do the following: . Effect menu Tap the EFFECT key . Voice Change menu Tap the V.CHANGE key . Setup menu (system setup) Press and hold down the CD EFF/ SETUP key . Tempo/Key menu Tap the TMP/KEY key . CD Effect menu Tap the CD EFF/SETUP key . Metronome menu Press and hold down the STOP key. The menu then shows the menu category you select, reversed and blinking. Menu Category EFFECT Menu Item EFF Values (default values are underlined) 01-18 Notes sets the number of the effect preset PAR – sets the effect parameter VOICE CHANGE VCHG DN, OFF, UP sets the voice change function SETUP MIX M10 – M1, 0, C1 – C10 sets the mix balance between CD and input PLAY ALL/SGL selects all or single play CUE CUE/FLS selects the action of the CUE key UPDN MIX, TMP, KEY, FIN Sets the UP/DOWN key function in the home display mode CAL 435 – 440 – 445 sets base frequency (A4, unit: Hz) OSC (OFF), _C–_B, C-A, B, _ C– _ B, (3 octaves) sets the pitch of the oscillator 14 — TASCAM CD-VT1MKII Using the menu system Menu Category Menu Item Values (default values are underlined) Notes TEMPO KEY TMP VSA=OFF: -50 to +16 VSA=ON: -50, -32, -16,-12, -8, -4, 0, +4, +8, +12, +16 sets the speed of CD playback in % VSA ON/OFF turns VSA on or off KEY I6 – 0 – O6 sets key control in semitones FINE -50 – 0 – +50 sets fine tuning (cent) CD EFF CNCL ON/OFF turns vocal cancel function on or off selects the stereo region PART L10 – L1, C, R1 – R10 reduced by the vocal cancel function RNGE MID/ALL selects the range reduced by the vocal cancel function MONO OFF (stereo), L+R, L, R selects mono monitor mode SPLT OFF (mix), C-M, M-C selects split monitor mode METRONOME MTRO (OFF), 40 – 120 – 220 sets tempo of metronome in BPM (Beats Per Minute) BEAT OFF, 2 – 6 selects number of beats of the metronome Choosing menu items Choose menu items in the selected menu category using the PREV and NEXT keys. Changing the setting values Change the setting values using the UP and DOWN keys. Exiting the menu system Press the TIME/ESC key to exit the menu system and go back to the home display mode. TASCAM CD-VT1MKII — 15 Using the CD player The CD player in CD-VT1MKII works in much the same way as other CD players, with a few minor differences and special features. Playback Press the PLAY/PAUSE key (G/J) to start playback and to pause playback. Press the STOP key (H) to stop playback. Skipping between tracks and searching within tracks Use the skip/search keys (m/.. and //,) to move back and forward one track at a time. Use these keys to search within the CD by pressing and holding the key for the direction that you want to search. By continuing to press, the search will speed up. Looping (track/disc) Press the LOOP key to repeat a single track, or all tracks, according to the PLAY...