Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
Any other product may damage the player. 1 Make sure that the adapter’s voltage corresponds to the local voltage. 4,5VDC 2 Connect the adapter to the 4.5V DC socket of the player and to the wall socket. Note: Always disconnect the adapter when you are not using it. HEADPHONES HE 035 • Connect the supplied headphones to the p/LINE OUT socket of the player. Note:p/LINE OUT can also be used for connecting the player to your HiFi system (with a signal lead) or to your car radio (with a cassette adapter or signal lead). In both cases, the volume of the player must be set to position 8. IMPORTANT! Hearing safety: Do not play your headphones at a high volume. Hearing experts advise that continuous use at high volume can permanently damage your hearing. Traffic safety: Do not use headphones while driving a vehicle. It may create a hazard and it is illegal in many countries. Even if your headphones are an open-air type designed to let you hear outside sounds, do not turn up the volume so high that you cannot hear what is going on around you. CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure. PLAYING A CD This CD player can play all kinds of Audio Discs such as CD-Recordables and CD-Rewritables. Do not try to play a CD-ROM, CDi, VCD, DVD or computer CD. 1 Push OPEN 2 to open the CD compartment lid. 2 Insert an audio CD, printed side up, by pressing the CD center onto the hub. 3 Close the player by pressing the lid down. 4 Press 2; to switch the player on and start CD playback. yThe current track number and the elapsed playing time are displayed. • You can pause playback by pressing 2;. yThe time where playback was paused will flash. • You can continue playback by pressing 2; again. 5 Press 9 to stop playback. yThe total number of tracks and the total playing time of the CD are displayed. 6 Press 9 again to switch off the player. • To remove the CD, hold it by its edge and press the hub gently while lifting the CD. Note: If there is no activity, the unit will automatically switch off after a while to save energy. 0 MODE PLAYBACK INFORMATION • If a CD-Recordable (CD-R) or a CD-Rewritable (CD-RW) is not recorded properly, nF dISC is displayed. In that case, use FINALIZE on your CD- recorder to complete the recording. • If you want to play a CD-Rewritable (CD-RW), it takes 3–15 seconds for sound reproduction to start once you have pressed 2;. • Playback will stop if you open the CD lid. • While the CD is being read, 1-:-flashes in the display. VOLUME AND BASS Volume adjustment Adjust the volume by using VOL E. Bass adjustment • y Press BASS switch the bass enhancement off activated. PROGRAMMODE SELECTING A TRACK AND SEARCHING Selecting a track during playback • Briefly press . or § once or several times to skip to the beginning of the current, previous or next track. yPlayback continues with the selected track, and its number is displayed. Selecting a track when playback is stopped 1 Briefly press . or § once or several times. PROGRAMMODE yThe selected track number is displayed. 2 Press 2; to start CD play. yPlayback starts with the selected track. Searching for a passage during playback 1 Keep . or § pressed to find a particular passage in a backward or forward direction. ySearching is started and playback continues at low volume. After 2 seconds the search speed increases. 2 Release the button when you reach the desired passage. yNormal playback continues from this position. Notes: – During SHUFFLE, SHUFFLEREPEATALL, REPEAT or while playing a program, searching is only possible within the particular track. PROGRAMMING TRACK NUMBERS You can select up to 15 tracks to play in a program. A single track may be played more than once in the program. 1 While playback is stopped, select a track with . or §. 2 Press PROGRAM to store the track. yPROGRAM lights; the track number programmed and P, with the total number of stored tracks, are displayed. 3 Select and store all desired tracks in this way. 4 Press 2; to start playback of your selected tracks. yPROGRAM is shown and playback starts. • You can review the program by pressing PROGRAM for more than 2 seconds. yThe display shows all stored tracks in sequence. Notes:– If you press PROGRAM and no track is selected, SELECtis displayed. –If you try to store more than 15 tracks, FULLis displayed. Clearing the program • While playback is stopped, press 9 to clear program. yCLEAr is displayed once, PROGRAM disappears, and the program is cleared. Notes: – The program also will be cleared if you –interrupt the power supply, or – open the CD compartment lid, or –if the unit switches off automatically. This product complies with the radio interference requirements of the European Union. Both the model number and production number are located on the bottom of the set. MODE TROUBLESHOOTING It is possible to play tracks in random order, to repeat a PROGRAM If a fault occurs, first check the points listed below be...