It will solder from 35 to 100 joints per charge, depending upon type of application. A finger-tip ON-OFF button is provided for safety and convenience. For operational safety and proper use of the Soldering Pencil, please read all safety rules and instructions. Don’t forget to send in the guarantee registration card. THANK YOU FOR BUYING BLACK & DECKER! SOLDERING PENCIL SAFETY RULES 1. WHEN NOT IN USE, store the tool in a dry, high or locked-up place — out of the reach of children. 2. KEEP

Be sure that the soldering ip has been freshly tinned. When you press the switch button, the work light will come on and the tip will start heating immediately. In about 6 seconds, with light pressure, toucfi the tip to the connection, and at the same time, feed the solder to the spot being heated by the tip. After enough solder melts to just cover the connection, release the button, lift the tip and ailow solder to cool. Do not disturb the connection until solder has hardened. Pencil can be pl

However, after several charge and discharge cycles, the battery will be back up to its full capacity. 3. While charging, the Charger may hum and become warm to touch. This is a normal condition* and does not indicate a problem. 4. If the battery does not charge properly—(!) check power supply at receptacle by plugging in a lamp or other appliance, (2) check to see if receptacle is connected to a light switch which turns power of when you turn out the lights, 5. Whenever you unplug the Charger

Disconnect the main AC input power to the 3. Remove the red insulating paint from the machine. heat sink test points. See Figure F.17. DO NOT DISASSEMBLE THE HEAT SINKS. 2. Locate and disconnect plug J9 from the thermal fan/snubber board and plug J5 from the firing board. See Figure F.16. IDEALARC DC-655 Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOCReturn to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC F-40 F-40 TROUBLESHOOTI

CAN-2.21-M85 . IAS US. 4-96 GSST8N NATURAL GAS GSST8P PROPANE - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. - WHAT TO DO IF YOU SMELL GAS: . Do not try to light any appliance. . Do not touch any electrical switch; do not use any phone in your building. . Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions. . If you cannot reach your gas supplier, call the fire department. - Inst

(refer to your manual for clearances) Mark all 14 hole centres on the wall (surface) using the template. 2. Remove the template. Depending on the surface and fasteners, drill the appropriate holes. Hold the Torch up, aligning the mounting brackets to the mounting holes. Secure the Torch to the wall using the appropriate fasteners. NOTE: The Torch has been designed to have a 1/2” clearance between the rear outer panel and the mounting surface. 3. Start the fasteners into each of the six remaining

3. Clamp the workpiece between the two clips 5 . Q Solder sponge CAUTION! The hot soldering tip 2 must never be placed in contact with a dry solder sponge 8 , otherwise the solder sponge may be damaged. j The solder sponge 8 is used to clean soldering tips. j Moisten the solder sponge 8 before you use it. 14 GB/IE/CY Operation/Maintenance and cleaning grease or soldering fluid) as a flux. Clean the soldering tip 2 on the moist solder sponge 8 . After cleaning the tip 2 it must be “tinned” (coate

Both of these consumables are available from your authorized OK International distributor as needed. The power supply features a Power Switch, green “Power On” indicator light, power cord, and a connecting port for the solder handle cord. 1. Mount the power supply in a convenient location in your workspace, such as on the workbench. 2. Insert a heater tip onto the Coil Assembly and simply push the Heater Tip all the way until it seats. You should feel a slight “ click” as it locks into place. In

. Do not install unit near flammables. . Do not overload building wiring . be sure power supply system is properly sized, rated, and protected to handle this unit. STATIC (ESD) can damage PC boards. . Put on grounded wrist strap BEFORE handling boards or parts. . Use proper static-proof bags and boxes to store, move, or ship PC boards. H.F. RADIATION can cause interference. . High frequency (H.F.) can interfere with radio navigation, safety services, computers, and communicationsequipment. . Hav

3 PHASE OUTPUT CONDITIONS INPUT CURRENT AMPS IDLE POWER POWER FACTOR @ RATED OUPUT EFFICIENCY @ RATED OUPUT 460/500/575V 500A@40V.100% 31/29/25 800 Watts Max. .95 MIN. 84% OUTPUT OPEN CIRCUIT VOLTAGE CURRENT RANGE DC PULSE FREQUENCY PULSE VOLTAGE RANGE PULSE AND BACKGROUND TIME RANGE AUXILIARY POWER (CIRCUIT BREAKER PROTECTED) 90VDC 20-500 0.15 - 1000 Hz 5 - 55 VDC 100 MICRO SEC. 3.3 SEC. 40 VDC AT 10 AMPS 115 VAC AT 10 AMPS PROCESS CURRENT RANGES (AC or DC) CURRENT SAW / MIG / MAG FCAW Pulse 50