Votes - 4, Average rating: 4.5
(
)
)
|
manual abstract
27 Design Spot 575B™ Design Spot 575B™ the fixture will lock into the last DMX signal it received and remain in that position until it is turned off or begins receiving a new DMX signal. If the fixture is turned on without any DMX signal, the fixture will automatically go in to sound-active mode. Available settings are: “Close” – Shutter flags will close. “Hold” – Fixture will remain at it’s last settings. “Auto Program” – Fixture will go into stand-alone mode, running the built-in program. “Music Control” – The fixture will go into sound-active mode. C. Pan Reverse -This function allows you to invert all pan movements. Use the Up and Down buttons to turn this function On and Off. Press the Enter button to accept the change or the Mode button to cancel and return to the main menu. D. Tilt Reverse -This function allows you to invert all tilt movements. Use the Up and Down buttons to turn this function On and Off. Press the Enter button to accept the change or the Mode button to cancel and return to the main menu. E. Fine resolution – This function changes the DMX channel operation from 8bit to 16bit. F. Pan Degree – This function changes the maximum Pan resolution from either 540° or 630°. The default function is 540°. G. Feedback – This function turns the feedback correction on or off. This function is set to on as default. H. Movement Speed – This function changes the order of the DMX channels to more closely match similar fixtures from different vendors, thus allowing the user easier functionality when programming. There are four different mode variations. I. Mic Sensitivity – This function make the internal microphone more or less sensitive to sound. This function only works in conjunction with the sound active modes. The default setting is 70% and setting range from 0 % to 99 %. 9.4.2. Service Settings – These adjustments and settings should only be performed by a technician familiar with the functionality this fixture. Incorrect setting of these ©Elation Professional, Los Angeles CA. 28 Design Spot 575B™ Design Spot 575B™ functions may result reduced performance or damage to the fixture. Service Password: The correct password must be entered before attempting wheel calibration, changing fan voltage, or changing the gobo speed. Fan Voltage: This function will change the fan voltage from either “Low” or “High.” Low will send normal voltage to the fan, for normal operation. High will send slightly higher voltage to fans that allows the fans to operate at higher than normal speeds. This setting should only be used in extreme cases of higher than normal temperatures. Using the fans in “HIGH” mode will decrease fan life over time. Low is the default setting. Gobo Speed: This function will change the speed at which the gobo wheel moves. This function allows Design Spot 575Bs and Design Spot 250s to be implemented together in the same rig. There are two different settings, “Quick” and “Slow.” Slow will move the gobo wheel at a speed that matches the first generation Design Spot 250. The “Quick” setting will advance the wheel at a new, faster rate than the original Design Spot 250. “Quick” is the default setting. 9.4.3. Fans Control -This function is used to change the functionality of the internal cooling fans. The available selections are: 1) “AUTO” – The fans will automatically switch between low and high speeds depending on the internal operating temperature. 2) “HIGH” – The fans will run in high-speed mode regardless of operating temperature. 3) “LOW” – The fans will remain in low speeds regardless of internal operating temperature. 9.4.4. Temperature C/F – This function changes the temperature unit readout from either the temperature Celsius or Fahrenheit. 9.4.5. Initial effect -With this function, you can adjust with which value the respective channels will start. 9.4.6. Restore Default -With this function you can restore the factory settings of the device. All settings will be set back to the default values (shaded). Any edited ©Elation Professional, Los Angeles CA. 29 Design Spot 575B™ Design Spot 575B™ scenes will be lost. 9.5 Reset Functions: 9.5.1 Reset All: This function will reset all internal motors to the home position. 9.5.2 Reset Pan and Tilt: This function will only reset the pan and tilt motors to the home position. 9.5.3 Reset Colors: This function will only reset the color wheel and the CMY filter motors to the home position. 9.5.4 Reset Gobos: This function will only reset the gobo wheels to the home position. 9.5.5 Reset Shutter: This function will only reset the blackout shutter to the home position. 9.5.6 Reset Others: This function will reset all other motors to the home position. 9.6 EFFECT ADJUST: 9.6.1 Test Channel – This menu function allows the user to select each individual fixture channel and test it’s function independently from the control board. 9.6.2 Lamp adjustment (manual control) – This function readies the fixture for lamp optimization in a simple single step procedure....