Votes - 0, Average rating: 0
(
)
)
|
manual abstract
02- The fitting is not suitable for installation in bathrooms at least not in the specified zone. 03- The fitting is suitable for fixing to normal flammable surfaces. Recessed luminaires should under no circumstances be covered with insulation material or other similar materials. 04- This product is not suitable for direct mounting on flammable surfaces. 05- The fitting may be covered with insulating material. 06- The fitting is only suitable for fixing to the ceiling. 07- The fitting is only suitable for fixing to the wall. 08- The fitting is suitable for fixing to the wall and to the ceiling. 09- Always observe the minimum distance between the lamp and the surface being lit as indicated on the icon. 10- IPX1: The fitting is protected against dripping water. 11- IPX3: the fitting may be exposed to raindrops (falling drops under a maximum angle of 60° to the vertical axis). 12- IPX4: the fitting is splash-proof: it may be exposed to splashing water coming from any direction (360°). 13- IPX5: The fitting is protected against water jets. 14- IPX7: The fitting can be installed into the ground. 15- IPX8: offers protection against immersion up to the indicated depth. 16- IP5X: The fitting is dust protected. 17- IP6X: The fitting is dust tight. 18- Immediately replace a cracked or broken safety glass and use only manufacturer approved parts. 19- Protection class I: the fitting has an earthing connection. The earth wire (yellow/green) has to be connected to the clip marked with . 20- Protection class II: the fitting is double insulated and must not be connected to an Earth. 21- Protection class III: the fitting is only suitable for very low voltage supply (e.g. 12V). 22- Strip the wire as indicated in the diagram. 23- The earthing wire always has to be longer than the contact wires. 24- The use of the supplied heat-resistant sleeving is required over the unstripped wire lengths. 25- Use heat-resistant cable for wiring the fitting into the mains. 26- The fitting is only suitable for wiring directly into the mains. 27- X-connection: In case of damage to the wire, it has to be replaced by a wire of the same type. Y-connection: In case of damage to the wire, it has to be replaced only by the manufacturer, distributor or by an expert, to avoid risks. Z-connection: The wire can’t be replaced. 28- MAX. …W: only use lamps suitable for this fitting and keep within the maximum specified wattage. 29- The fitting is only suitable for reflector lamp(s). EN SAFETY INSTRUCTIONS - PART B 30- The fitting is only suitable for PLCE lamps. 31- The fitting is not suitable for PLCE lamps. 32- Only an incandescent lamp with a diameter of 60mm can be used. A lamp with a 45mm diameter must not be used for this fitting. 33- Only use an incandescent globe bulb that is the size of the indicated diameter. Never use a standard incandescent bulb. 34- This product is only suitable for candle shaped bulbs. 35- Never use "cool-beam" lamps for this fitting. 36- The fitting is only suitable for a lamp with built-in safety or a low pressure lamp. An extra safety glass is not necessary. 37- Capsule and linear halogen lamps may not be touched by bare hands. 38- The fitting is equipped with a fuse. If the fitting is out of order after the bulb has been replaced, the internal fuse has to be replaced. If contact with the internal wiring can be made during this operation, this should be done by a competent electrician. 39- The fitting can be used in combination with a dimmer with exception where PLCE-lamps are used. Consult a qualified electrician for choosing the right type (especially important for 12V-fittings). 40- The fitting is working with a safety transformer. Replace a broken transformer only with a transformer with identical technical specifications. Consult a qualified electrician or your retail outlet. 41- Fittings for rough use. 42- Fitting with time and light setting options. Minimum and maximum will be shown in the icon in part A. 43- The fitting can be placed at a maximum of 6 meters height. 44- To reach an optimal working, you have to place the fitting on the height mentioned in the icon. The maximum and minimum reach of the detector is also mentioned in the icon in part A. 45- The standard active range of vision of the detector covers the given degrees mentioned in the icon. 46- This fitting should be mounted horizontally. For longer life, the bulb should not be at a greater angle than 4 degrees. 47- Ensure that you don’t drill through electrical wires or any other obstruction in the wall or ceiling during installation! 48- If the luminaire is mounted onto a ceiling-box or wall-box, it is obliged to cover the box with a lid first. (e.g. The Netherlands) 49- Electrical wiring may never be clamped or twisted between the luminaire and the mounting surface ! 50- Luminaires designed for use with bowl mirror lamps. 51- This luminaire contains in some places very hot parts. 52- This product is not suitable for children under 14 years. The lighti...