Login:
Votes - 4, Average rating: 4 ( )

User manual ATN, model ATN NVG7

Manafacture: ATN
File size: 613.66 kb
File name: cb078dd7-4bbf-4434-9488-b4f26aff6d2c.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


It also will act as a daylight filter, allowing you to test the scope in daylight or other bright light situations. The pinhole in the center of the protective cover allows the user to check the operation ability of the device in daylight conditions. NOTE: Do not test the scope in daylight conditions even with the daylight filter/lens cap on for more than ten (10) minutes. operATion • Take the monocular out of the case. • Install the battery into the housing with the polarity order as shown on the scope. Battery Type: 3 Volt Lithium, #CR123A . • Press the button (short press -less than 1.5 sec.) to turn the unit on by the protective lens cover still attached to the lens. Do not turn the unit on in the daytime without the protec. tive lens cap on. You should see green glow in the eyepiece. • Observe the scene and adjust the diopter for optimal image clarity. • You may now enter a dark environment or simply shut the lights off in order to darken the room. • Next, remove the lens cap/daylight filter. Adjust the front lens for the distance of the focus. You should not have to readjust the diopter. • To turn the unit off, push the button again by short press (less than 1.5 sec.). .oc.sing To focus the NVG-7, first you will need to adjust the diopter. Simply turn the diopter clockwise until it stops. Then, while looking throught the diopter at an object, slowly turn the diopter back counter clockwise until the grain in the image is sharp. NOTE: We suggest that you focus the diopter during daylight with the filter on. Next focus the front lens until the image and the grain are both sharp. When you are in low-light conditions and the daylight filter is off, you may focus the front lens to receive sharp image, the diopter should not be adjusted. NOTE: The front lens should be readjusted as you view objects at different distances. in.rA-red ill.minATor Diopter adjasting Lens focus adjusting Built-in Infra-red Illuminators Infra-red illuminators, or IR illuminators, are common to night vision. The IR light greatly enhances the performance of the NVG-7 while remaining almost totally invisible to the naked eye. The NVG-7 goggles have a built in IR with indicator “ON” light within the FOV. To turn the IR on, push the button by long press (more than 1.5 sec.). It is important to remember that the IR illuminator is simply an infra red light source, and like any light source, it may loose its effectiveness over a great distance. To turn the IR off, push the button again by long press (more than 1.5 sec.). NOTE: The IR will automatically turn off when the unit’s power is turned off. flip.up heaDSet fittinG the heaDGeaR 1) Fit the headgear to your head size. Adjust the head gear fist before attaching the NVG-7 to it. 2) Loosen all the straps and place the headgear onyour head. 3) Tighten the straps until the headgear fits firmly. GooGleS inStallation anD aJuStment Now you are ready to mount the NVG-7 on to your headgear. 1) Remove the already adjusted headgear from your head. 2) Push button [1] and insert the bracket [2] of the NVG-7 to the rail of the headset. 3) Place the headgear with NVG-7 onto your head. 4) Loosen the screw [3] and move the unit along the rail for eye relief adjustment . The NVG-7 headset has a flip-up mechanism. Push the button [4] on the side of mount and lift the unit up until the unit fixates in the top position. Push same button to lower NVG-7 to viewing position. If you need increase the eye relief of your goggles, you can displace the bracket on the top of NVG-7. 1) Unscrew the screw and detach the end-cap from the bracket of NVG-7. 2) Unscrew the 2 screws and detach the bracket from the NVG-7 body. 3) Turn the bracket 180 degrees. 4) Screw the 2 screws back into place. 4 1 3 2 helmetmount (optional) Helmet mount for attachment of ATN’s NVG-7 to a standard PASGT helmet. Helmet mount fits securely onto helmet via a rugged strapping device and grooved hooks. With helmet mount, NVG-7 can be positioned directly in front of user’s eyes or flipped. inStallation 1) Install the mount onto helmet as shown on the picture. 2) Tighten and fixate the straps [1] 3) Attach goggles to the rail. Push button [2] and insert the bracket of the NVG-7 to the rail of the mount. 4) Place the helmet on your head. aDJuStment 1) Loosen the screw [3] and move the unit along the rail for eye relief adjustment.Tighten the screw [3]. 2) Loosen the top vertical fixation screw [4]. Adjust goggle vertical position.Tighten vertical position screw. 3) The NVG-7 helmet mount has a flip-up mechanism. Push a button [5] on the side of mount and lift the unit up till fixation in the top position. 2 1 1 3 4 5 4 3X afocal lenS (optional) The NVG-7 with 3X or 5X front lens can be used as a powerful night vision bi-ocular. To install 3X Afocal Lens screw it on the front lens of NVG-7. To install 5X lens unscrew the objective lens of NVG-7 and screw F112 Lens to the free place (make sure that the unit is turned off). StoRaGe anD caRe 5X Lens ...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category