Votes - 1, Average rating: 4
(
)
)
|
manual abstract
If the diopter is not adjusted to correspond to your eyesight, you may not be able to clearly focus your subject. 4. Measuring Note: Depressing and holding down the POWER button causes all symbols to be displayed in the LCD panel. After you remove your finger from the POWER button, the last-used setting is displayed. (If you briefly press the POWER button then remove your finger, the LCD panel may display the last-used setting without displaying all of the symbols. This is not a malfunction or other problem.) [Deciding which Target Priority to use] When obtaining different results from a single measuring operation, the Laser 1200S will display the distance to the farthest target on the LCD panel when using Distant Target Priority mode, while First Target Priority mode will show the range to the nearest target. ex.) When measuring a tree standing in front of a house; “135m” (distance to the tree) will be displayed in First Target Priority mode, and “157m” (distance to the house) in Distant Target Priority mode. First Target Priority mode, for example, has applications for golf, while Distant Target Priority is useful when hunting in heavily wooded areas. 7. Backlight Use the backlight to see the LCD panel in dark conditions. By pressing MODE button briefly (less than 1.5 seconds) while the power is on, the backlight can be turned ON and OFF. The backlight can also be turned off by turning the Laser 1200S’s power off. In this case, the backlight will be off when the Laser 1200S’s power is turned on again. 8. Low battery indication Flashing indicates that the battery charge is low and battery should be replaced. (See “Changing Battery”) Tree House Distance to target 135m 157m 6. Selecting target priority Target Priority Switch System allows you to select display mode from First Target Priority and Distant Target Priority. POWER button Keep pressing The instrument continuously measures distance for 20 seconds • Continuous measurement 5. Select unit of measurement: m (meter) or YD (yard) Meters [ ] Yards [ ] Press and hold MODE button for more than 1.5 seconds until the display changes First Target Priority [ ] Distant Target Priority Changing Battery • Type of battery: 3V CR2 lithium battery • Battery condition indicators : Battery has enough charge for use. : Battery charge is getting low. flashing: Battery charge is low and battery should be replaced. disappears: Battery is exhausted and should be replaced. flashing in the LCD indicates that the battery should be replaced. 1 Open the battery chamber cover Insert a coin or similar item into the slot in the battery chamber cover, and rotate it following the “Open/Close” indication. The cover may not open easily due to its O-ring seal for water and dust resistance. 2 Replace the old battery with a new one Install new battery with the [+] and [-] correctly positioned following the “Battery installation” indication seal in the battery chamber. (Insert battery positioning the [+] pole towards the inside of the chamber.) [The Laser 1200S will not operate if the battery is installed incorrectly.] 3 Close the battery chamber cover Screw the cover back in place using a coin or similar item. The cover may not close easily due to the O-ring seal for water and dust resistance. Confirm that the cover is correctly closed. • Battery life Continuous operation: Approx. 5,000 times (with backlight off at 20°C) Target focusing, measurement, and automatic power off are included in a single cycle. This figure may differ according to temperature, and other factors such as target shape, color, etc. * The Laser 1200S comes with a 3V CR2 lithium battery. However, due to natural electric discharge, the life of the battery will likely be shorter than that noted above. Replace battery if the Laser 1200S is ever submerged in water or if water enters the battery chamber. The Nikon Laser 1200S features a Roof-prism monocular optical system for viewing your target. A liquid crystal display (LCD) is mounted within the optical system that when activated, displays a reticle for targeting, meter/yard and Target Priority and a target quality gauge, as well as precision and low battery indicators. It is also equipped with a built-in backlight. Specifications Troubleshooting/Repair If problems persist after consulting the Troubleshooting Table, please contact your local dealer to check/repair the Laser 1200S. Never let anyone other than the official representative of the product manufacturer check or repair the Laser 1200S. Failure to follow this instruction could result in injury, or damage to the product. Symptom Check Points Unit does not turn on — LCD fails to illuminate Target range cannot be obtained [- - - -] (“Cannot measure”) appears Closer target cannot be measured Target beyond a certain distance cannot be measured Measurement result is unstable Incorrect result is displayed • Depress POWER button. • Check and replace battery if necessary. • Be sure that nothing, such as your hand or fin...