Votes - , Average rating:
(
)
)
Manafacture: Dell
File size: 943.36 kb
File name:
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
Other manuals for this model:
manual abstract
10. Remove the display assembly from the computer base. Replacing the Display Assembly 1. Align the display assembly hinges with the holes in the base of the computer and then lower the display into place. 2. Replace and tighten the two display assembly hinge screws. 3. Carefully route the display cables and the speaker cable into their routing guides and connect them to the respective system board connectors. 4. Carefully slide the Mini-Card antenna cables through the system board and into their routing guides. 5. Replace the palm rest (see Replacing the Palm Rest). 6. Replace the keyboard (see Replacing the Keyboard). 7. Replace the module cover (see Replacing the Module Cover). 8. Slide the battery into the battery bay, until it clicks into place and slide the battery-lock latch towards the lock position. Display Bezel 1 display cables 2 Mini-Card antenna cables 3 speaker cable 1 display cable connectors 2 screw (2) 3 speaker cable connector Removing the Display Bezel 1. Follow the instructions in Removing the Display Assembly. 2. Using your fingertips, carefully pry up the inside edge of the display bezel. 3. Remove the display bezel. Replacing the Display Bezel 1. Realign the display bezel over the display panel, and gently snap into place. 2. Follow the instructions in Replacing the Display Assembly. Display Panel Removing the Display Panel 1. Follow the instructions Removing the Display Assembly. 2. Remove the display bezel (see Removing the Display Bezel). 3. Remove the camera (see Removing the Camera). 4. Remove the six screws securing the display panel assembly to the display cover. 5. Remove the display panel assembly. NOTICE: The display bezel is extremely fragile. Be careful when removing it to prevent damaging the bezel. 1 display panel 2 display bezel 6. Remove the four screws (two on each side) that secure the display panel brackets to the display panel. Replacing the Display Panel 1. Attach the display bracket to the display panel by replacing the four screws (two on each side of the display panel). 2. Align the display assembly panel with the display cover and replace the six screws. 3. Replace the camera (see Replacing the Camera). 4. Replace the display bezel (see Replacing the Display Bezel). 5. Follow the instructions in Replacing the Display Assembly. Display Panel Cable 1 display cover 2 screw (6) 3 display panel 1 screw (4 total; 2 on each side) 2 display panel bracket (1 left, 1 right) Removing the Display Panel Cable 1. Follow the instructions in Removing the Display Assembly. 2. Remove the display bezel (see Removing the Display Bezel). 3. Remove the camera (see Removing the Camera). 4. Remove the display panel (see Removing the Display Panel). 5. Turn over the display panel and place it on a clean surface. 6. Lift the conductive tape that secures the flex cable to the display board connector and disconnect the flex cable. Replacing the Display Panel Cable 1. Connect the flex cable to the display board connector and secure it with the conductive tape. 2. Replace the display panel (see Replacing the Display Panel). 3. Replace the camera (see Replacing the Camera). 4. Replace the display bezel (see Replacing the Display Bezel). 5. Follow the instructions in Replacing the Display Assembly. Back to Contents Page NOTE: The Display Panel cables and connectors may differ depending on the Display Panel you ordered. 1 back of display panel 2 flex cable 3 conductive tape 4 display board connector Back to Contents Page Keyboard Dell™ Vostro™ A90 Service Manual Removing the Keyboard Replacing the Keyboard For more information about the keyboard, see the Dell Technology Guide. Removing the Keyboard 1. Follow the instructions in Before You Begin. 2. Turn the computer over. 3. Remove the two screws from the base of the computer. 4. Turn the computer top-side up and open the display. 5. Carefully lift the keyboard and hold it to access the keyboard connector. 6. Push out the securing tabs that secure the keyboard cable to the system board and remove the keyboard. CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the computer. NOTICE: The keycaps on the keyboard are fragile, easily dislodged, and time- consuming to replace. Be careful when removing and handling the keyboard. NOTICE: Be extremely careful when removing and handling the keyboard. Failure to do so could result in scratching the display panel. NOTICE: The securing tabs that secure the keyboard cable to the system board are fragil...