Votes - 1, Average rating: 5
(
)
)
|
Other manuals for this model:
manual abstract
2. Remove the computer cover (see Removing the Computer Cover). 3. Grasp the drive-release latch and slide it towards the base of the computer until the drive panel snaps open. 4. Pivot the drive panel outward and lift it from its side hinges. 5. Set the drive panel aside in a secure location. Installing the Drive Panel 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Align the drive panel tabs with the side-door hinges. 4. Rotate the drive panel toward the computer until it snaps into place on the drive panel. 5. Replace the computer cover (see Replacing the Computer Cover). 1 drive-release latch 2 drive panel 3 drive-panel tabs 1 drive-release latch 2 drive panel 3 drive-panel tabs See the documentation that came with the drive for instructions on installing any software required for drive operation. Floppy Drive Removing a Floppy Drive 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the drive panel (see Removing the Drive Panel). 4. Disconnect the power and data cables from the back of the floppy drive. 5. Slide the drive-release latch towards the base of the computer to release the shoulder screw, and then slide the drive out of the drive bay. 6. Replace the drive panel (see Installing the Drive Panel). CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. 1 power cable 2 floppy drive data cable 1 drive-release latch 2 floppy drive 7. Replace the computer cover (see Replacing the Computer Cover). 8. Connect your computer and devices to electrical outlets, and then turn them on. Installing a Floppy Drive 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the drive panel (see Removing the Drive Panel). 4. Remove the existing floppy drive, if applicable (see Removing a Floppy Drive). 5. If no screws are attached to the new floppy drive, check the inside of the drive panel for shoulder screws. If screws are present, attach the screws to the new drive. Slide the floppy drive into the drive bay until it clicks into place. 6. Connect the power and data cables to the back of the floppy drive. 7. Check all cable connections and fold cables out of the way to avoid blocking airflow between the fan and cooling vents. 8. Replace the drive panel (see Installing the Drive Panel). 9. Replace the computer cover (see Replacing the Computer Cover). NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer. 1 floppy drive 2 shoulder screws (4) 1 drive release latch 2 floppy drive NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it in to the computer. 10. Connect your computer and devices to electrical outlets, and then turn them on. See the documentation that came with the drive for instructions on installing any software required for drive operation. 11. Enter system setup (see Entering System Setup), and select the appropriate Diskette Drive option. Media Card Reader Removing a Media Card Reader 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the drive panel (see Removing the Drive Panel). 4. Disconnect the power and data cables from the back of the Media Card Reader. 5. Slide the drive-release latch towards the base of the computer to release the shoulder screw, and then slide the media card reader out of the drive bay. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. 1 media card reader power cable 2 system board connector 6. Replace the drive panel (see Installing the Drive Panel). 7. Replace the computer cover (see Replacing the Computer Cover). 8. Connect your computer and devices to electrical outlets, and then turn them on. Installing a Media Card Reader 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the drive panel (see Removing the Drive Panel). 4. Remove the existing media card reader, if applicable (see Removing a Media Card Reader). 5. If no screws are attached to the Media Card Reader, check the inside of the drive panel for shoulder screws. If screws are present, attach the screws to the new card reader. 6. Slide the Media Card Reader into the drive bay until it clicks into place. 7. Attach the power and data cables to the back of the Media Card Reader. 8. Check all cable connections and fold cables out of the way to avoid blocking airflow between the fan and cooling vents. 9. Replace the drive panel (see Installing the Drive Panel). 1 drive-release latch 2 media card reader NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the comp...