Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
Notebooks and Netbooks - Precision M4400 (822.47 kb)
Notebooks and Netbooks - Precision M4400 (819.9 kb)
manual abstract
If you use excessive force, you may damage the connector. Back to Contents Page Hinge Covers Dell Precision™ Service Manual Removing the Hinge Covers Replacing the Hinge Covers Removing the Hinge Covers The hinge covers are not interchangeable; the left one covers the multimode DisplayPort and the right one covers the RJ-45 network connector. 1. Follow the procedures in Before Working on Your Computer. 2. Close the display and turn the computer over. 3. Remove the bottom of the base assembly (see Removing the Bottom of the Base Assembly). 4. Remove the two M2.5 x 5-mm screws from each hinge cover. 5. Slide each hinge cover off the computer and lift to remove it. Replacing the Hinge Covers 1. Slide the left hinge cover over the display port and slide the right hinge cover over the RJ-45 network connector. 2. Replace the M2.5x5-mm screws in each hinge cover. 3. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly). 4. Follow the procedure After Working on Your Computer. Back to Contents Page CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. 1 display port 2 M2.5 x 5-mm screw (4) 3 RJ-11 network connector 4 hinge cover (2) Back to Contents Page Keyboard Dell Precision™ Service Manual Removing the Keyboard Replacing the Keyboard Removing the Keyboard 1. Follow the procedures in Before Working on Your Computer. 2. Remove the LED cover (see Removing the LED Cover). 3. Remove the two M2 x 3-mm screws along the top of the keyboard. 4. Using the pull tab, gently lift the top of the keyboard only, then lift out at an angle to remove the keyboard from its connector. Replacing the Keyboard 1. Holding the top of the keyboard slightly above the computer, slide the bottom of the keyboard in at an angle, and fit the tabs and keyboard connector along the bottom of the keyboard beneath the front-inside edge of the palm rest. 2. Carefully press each side to snap the keyboard into place. 3. Replace the two M2 x 3-mm screws at the top of the keyboard. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: The key caps on the keyboard are fragile, easily dislodged, and time-consuming to replace. Exercise care when removing and handling the keyboard. 1 keyboard 2 blue pull tab 3 M2 x 3-mm screw (2) CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. NOTICE: The key caps on the keyboard are fragile, easily dislodged, and time-consuming to replace. Exercise care when removing and handling the keyboard. NOTE: Pressing down on the ALT keys helps to seat the keyboard properly. 4. Replace the LED cover (see Replacing the LED Cover). 5. Close the display and turn the computer over. 6. Follow the procedure After Working on Your Computer. Back to Contents Page 1 keyboard connector 2 tabs (5) 3 M2 x 3-mm screw (2) Back to Contents Page LED Cover Dell Precision™ Service Manual Removing the LED Cover Replacing the LED Cover Removing the LED Cover 1. Follow the procedures in Before Working on Your Computer. 2. Open the display. 3. Using a plastic scribe, lift the right end of the LED cover. Lift the remainder of the cover to remove it from the laptop. Replacing the LED Cover 1. Snap the LED cover back into place one tab at a time. 2. Follow the procedure After Working on Your Computer. Back to Contents Page CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. 1 LED cover 2 scribe CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. Back to Contents Page Memory Dell Precision™ Service Manual Removing a Memory Module Replacing a Memory Module Verifying System Operation Removing a Memory Module Your system supports the following memory configurations: Your computer has two user-accessible SODIMM sockets, referred to as DIMM A and DIMM B. The socket closest to the system board, DIMM A, always contains a memory module. The DIMM B socket may contain an additional module for improved system memory performance. If the module in the DIMM A socket must be replaced and DIMM B is installed, DIMM B must be removed first. 1. Follow the procedures in Before Working on Your Computer. 2. Lay the computer upside down onto a clean, flat surface. 3. Remove the bottom of the base assembly (see Removing the Bottom of the Base Assembly). DIMM B The DIMM B socket may or may not be populated with a memory module, depending on the configuration of your system. When viewing the memory compartment from the underside of the computer, the DIMM B socket is uppermost and DIMM A is closest to the system board. Removing the DIMM B Module 1. To remove the DIMM B module, spread away the retaining clips from the side edges of the memory module and lift the free e...
Best service for manuals available in the web.