Run the Setup Utility and load the default values, then change the settings to the appropriate values as needed. If the problem persists, the internal clock battery may need to be replaced. Contact Panasonic Technical Support. 0271: Check date and time set-The data and time setting are incorrect. tings Run the Setup Utility and set the date and time correctly. If the problem persists, the internal clock battery may need to be replaced. Contact Panasonic Technical Support. 0280: Previous boot incomplete Startup has failed repeatedly, so the Setup Utility settings have been returned to their default - Default configuration used values, and the computer has been restarted. Run the Setup Utility and load the default values, then change the settings to the appropriate values as needed. 02B0: Diskette drive A error Disconnect the floppy disk drive and reconnect it. Make sure the drive is secured correctly. 0613: Serial Port*1 configura-I/O address and IRQ settings are in conflict. tion changed Run the Setup Utility and change the settings in [Advanced] menu so there is no port 0614: Serial Port*1 config. error conflicts. - device disabled *1 The port name, such as A or B, is displayed, indicating the conflicting ports. Press to resume, to Setup Write down the error details and press F2 to run the Setup Utility. Confirm the settings, and change the settings to the appropriate values as needed. Operating System not found The OS is not properly installed on the floppy disk or the hard disk that you are trying to boot from. If the computer cannot be booted from the floppy disk, check the floppy disk drive to ensure that the disk is in fact bootable, and change it to another if not. If the computer cannot be booted from the hard disk, confirm whether the hard disk is properly recognized in [Information] menu of the Setup Utility. If the hard disk is recognized, perform the reinstallation procedure. If not, contact Panasonic Technical Support. If a device is connected to the USB port, disconnect the device, or run the Setup Utility and set [Legacy USB Support] in [Security] menu to [Disable]. To run the Setup Utility 1 Restart the computer. 2 Press F2 while [Panasonic] boot screen is displayed soon after the computer begins the startup procedure. Troubleshooting Dealing with Problems (Summary) When a problem occurs, refer to this page. The “Reference Manual” also contains detailed information. If a problem appears to be related to a software application, read the software related manual. If you still cannot troubleshoot the problem, contact Panasonic Technical Support. You can use the PC Information Viewer to check the computer’s usage status. ( “Dealing with Problems (Advanced)”) Starting Up The power indicator or battery indicator is not lit Check the cable connection for the AC adaptor. Check to see if a fully charged battery is properly installed. Remove the battery pack and disconnect the AC adaptor, then connect them again. The computer does not operate when a USB device is connected The computer may not operate when certain USB devices are connected. Disconnect the USB device, or set [Legacy USB Support] to [Disable] in [Security] menu of the Setup Utility. [Enter Password] is displayed Input your Supervisor Password or User Password. If you have forgotten it, contact Panasonic Technical Support. POST Startup Error(s) is displayed page 25 Windows startup, or an op-Press F9 in the Setup Utility ( “Setup Utility”). This will restore the Setup eration is extremely slow Utility’s settings to their default values (except the password settings). Then, the Setup Utility must be run once again for you to input the appropriate operating environment settings. (The processing speed depends on the application software used, so this operation may not cause the processing speed to increase.) Disable any resident software. The date and time are incorrect You can set the date and time using the following menu. [start] - [Control Panel] - [Date, Time, Language, and Regional Options] - [Date and Time] If you continue to experience problems, the internal battery maintaining the clock may need to be replaced. Contact Panasonic Technical Support. When the computer is connected to a LAN, confirm the date and time of the server. This computer will not correctly recognize the date and time starting from the year 2100 A.D. When resuming from the Even when a password has been set in the Setup Utility, [Enter Password] does not apstandby or hibernation pear when the computer resumes from the standby or hibernation mode. mode, [Enter Password] If you want to use the security function when using the standby or hibernation mode, use does not appear even if a the Windows password as follows: password has been set in the 1 Select the account to change in [start] - [Control Panel] - [User Accounts] and set the Setup Utility password. 2 Add the check mark for [Prompt for password when computer resumes from standby] in [Control Panel] -...
)
