Votes - 5, Average rating: 4
(
)
)
|
manual abstract
(Brown wire) 2.5mm External microphone (Optional) Gnd (Black wire) LC Box (with fuse) Acc (Red wire) Figure 1: System diagram Instructions 1. Connect the 12V (Acc and Gnd) to car supply. 2. Connect the RCA-L and RCA-R to car stereo auxiliary (AUX) input. Alternately, you can use the RCA to 3.5mm jack cable (included) to connect to car stereo that supports 3.5mm AUX input. 3. Connect TEL-INT. pin to car stereo telephone mute line (if this feature is supported). 4. Make sure that the car stereo system’s telephone interrupt is ON. 5. Use Velcro with double-sided tape to hold the visor and Transceiver unit if necessary. (shown in Fig. 2). Detail of using Velcro will be explained as the followings: Step 1: Attach the Velcro hook to the visor clip with the double-sided tape provided. Step 2: Attach the Velcro loop to the hook. Step 3: Attach the Transceiver unit to the Velcro loop with the double-sided tape provided. 6. Secure the Transceiver unit to a location that is easily accessed by the driver e.g. sun visor (shown in Fig. 3) and dash board (shown in Fig. 4). 7. Set the left/right channel switch according to the position of driver (see “Switching left or right channel output” on page 23 for details). 8. Once the car is started, the Transceiver is powered on immediately. It cannot be turned off as long as the ignition key is turned to ON or ACC position. Notes: • Check that the location of the Transceiver is adequate to pick-up the car driver voice. • Alternately, user can use the external microphone (optional) that plug into the 2.5mm audio jack input for a better voice reception. 3. INSTALLATION Bluetooth® Audio/Mobile-phone Transceiver unit (step 3) Velcro loop (step 2) Velcro hook (step 1) Visor clip Figure 2: Using Velcro with double-sided tape 3. INSTALLATION Bluetooth® Audio/Mobile-phone Transceiver unit Figure 3: Fix the BLT370 to the car sun visor Bluetooth® Audio/Mobile-phone Transceiver unit Figure 4: Fix the BLT370 to the dashboard CAUTION ! • Please refer carefully to the system diagram before installing your BLT370. Incorrect wiring method may cause damage to BLT370, your car audio system or even your vehicle. • We strongly recommend that BLT370 is only installed by those fully familiar with your vehicle’s electrical system, please consult with the supply retailer if any doubt. 4. INTRODUCTION TO BLUETOOTH ® “PAIRING” What is Bluetooth® wireless technology? Bluetooth® wireless technology is a radio technology that connects devices, such as mobile phones and headsets, without wires or cords over a short distance of approximately 10 meters (approx. 33 feet). Get more information at What is Bluetooth® wireless profiles? Bluetooth® wireless profiles are the different ways that Bluetooth® devices communicate with other devices. Bluetooth® phones support either the headset profile (HSP), the hands-free profile (HFP) or both. In order to support a certain of profiles, a phone manufacturer must implement certain mandatory features within the phone’s software. The Bluetooth® Audio/Mobile-phone Transceiver unit supports both HSP and HFP profiles. In addition, it also supports A2DP and AVRCP in order to allow music streaming and playback control. Please refer chapter “Music Streaming and Playback Control” on page 19 for more description on these profiles. What is pairing? With a mobile phone featuring Bluetooth® technology, you must “pair” the Transceiver unit with the phone/Bluetooth® Audio Transmitter before you use it for the first time. “Pairing” creates a unique wireless link between the phone/Bluetooth® Audio Transmitter with Bluetooth® wireless technology and your Bluetooth® Audio/ Mobile-phone Transceiver unit eliminating the need to repeat the pairing process during future use. Bluetooth® devices will not work if the devices have not been paired. What is passkey? Passkey or PIN is a code that you enter on your mobile phone to pair it with the Transceiver unit. This makes your phone and the Transceiver unit recognize each other and automatically work together. 4. INTRODUCTION TO BLUETOOTH ® “PAIRING” Pairing Sequence Note: • Please refer to Clarion Bluetooth® Audio Transmitter and Cradle for iPod owner’s manual for the Bluetooth® Audio Transmitter operation below. Between Bluetooth® Audio/Mobile-phone Transceiver and Bluetooth® Audio Transmitter 1. Make sure the Transmitter is connected to an audio source. 2. Make sure the car stereo source mode is switched to ‘AUX’ mode. 3. Set the Transceiver unit in pairing mode. Please refer “Activating Bluetooth® Transceiver pairing mode” on page 17. 4. Set the Transmitter unit in pairing mode. 5. Music starts automatically upon successful pairing. Notes: • You do not have to enter a dedicated pin code for pairing these two devices, as you do with a mobile phone. • During pairing mode, the Transceiver unit should show a slower alternate red/blue LED. Make sure that the Transmitter and Transceiver are not paired to any other Transceiver or Tr...