It is recommended to: . Use electrical devices with prong power cords. . Use an extension cord with a hole receptacle and a prong plug at the opposite ends to ensure continuity of the ground protection from the unit to appliance. John Deere strongly recommend that all applicable federal, state and local regulations relating to grounding specifications be checked and followed. LINE TRANSFER SWITCH: If this unit is used for standby service, it must have a transfer switch between the utility power

READ THIS MANUAL carefully to learn how to operate and service your machine correctly. Failure to do so could result in personal injury or equipment damage. This manual and safety signs on your machine may also be available in other languages. (See your John Deere dealer to order.) THIS MANUAL SHOULD BE CONSIDERED a permanent part of your machine and should remain with the machine when you sell it. MEASUREMENTS in this manual are given in both metric and customary U.S. unit equivalents. Use only

The incoming wires and the compressor electrical connections should be checked. Loose connections will cause malfunctions. Unit does not make any or very little air Drain valve open Air leak Restricted or blocked intake Make sure the drain valve at the bottom of the tank is closed. Check the entire system for leaks, including the compressor unit and any piping attached to the compressor Make sure that the air intake of the compressor is not blocked in any way. Continued on next page 15 Operating

Refer to motor name plate for electrical ratings and specifications. 3. The line wire is the proper size and that no other equipment is operated from the same line. The chart gives minimum recommended wire sizes for compressor installations. MiniMuM pipe Size for CoMpreSSed Air line CfM length of piping System 25 feet 50 feet 100 feet 250 feet 10 20 40 60 100 1/2 inch 3/4 inch 3/4 inch 3/4 inch 1 inch 1/2 inch 3/4 inch 1 inch 1 inch 1 inch 3/4 inch 3/4 inch 1 inch 1 inch 1 inch 3/4 inch 1 inch 1

. . . . . . . . . . . . . . . . . . . . . . . .1 Safety Guidelines . . . . . . . . . . . . . . . . . . . . . .2 Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . .2 Important Safety Information . . . . . . . . . .2 Getting To Know Your Compressor . . . . .4 Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Maintenance. . . . . . . . . . .

3. Turning counterclockwise will lower air pressure at outlet. 4. Fully counterclockwise will shut off flow of air completely. Close Open Attach Hose Figure 8 REGULATED OUTLET GAUGE 1. This gauge shows at-a-glance, air pressure at outlet. Air pressure is measured in pounds per square inch (PSI). 2. Be sure this gauge reads ZERO before changing air tools or disconnecting hose from outlet. 2. Pull ring on safety valve and allow to snap back to normal position. Figure 10 ! WARNING Safety valve must

! CAUTION Overheating, short circuiting and fire damage will result from inadequate wiring, etc. GROUNDING INSTRUCTIONS 1. This product must be grounded. In the event of an electrical short circuit, grounding reduces risk of electrical shock by providing an escape wire for electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. Plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes

Use only genuine John Deere repair parts for your air compressor. Never make adjustments to the factory set pressures. Never exceed manufacturers maximum allowable pressure rating of attachments. Because of extreme heat, do not use plastic pipe or lead tin soldered joints for a discharge line. Never use air compressor to inflate small, low pressure objects such as toys. RISK OF BURSTING Serious injury or death may occur from an air tank explosion if air tanks are not properly maintained. Serious