Votes - 3, Average rating: 4
(
)
)
|
manual abstract
MAINTENANCE FUEL Fuel tank capacity: 0.66 US gal (2.5 f) Refuel in a well-ventilated area with the engine stopped. If the engine has been running, allow it to cool. Refer to page 41 for fuel recommendations and page 67 for information about oxygenated fuels. Never refuel the pump inside a building where gasoline fumes may reach flames or sparks. Keep gasoline lights, barbecues, electric appliances, away power from appliance tools, etc. pilot Spilled fuel is not only a fire hazard, Wipe up spills immediately. it causes environmental damage. Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Stop the engine and keep heat, sparks, and flame away. Handle fuel only outdoors. Wipe up spills immediately. 1. Remove the filler cap and check the fuel level. FILLER CAP 2. Refill the tank if the fuel level is \ low. Do not fill above the shoulder of the fuel filler neck. 3. After refueling, make sure the tank filler cap is closed properly and securely. MAINTENANCE ENGINE MAINTENANCE Engine Oil Change Drain the oil while the engine is warm. Warm oil drains quickly and completely. 1. Remove the oil filler cap, drain bolt and sealing washer. Drain the oil into a suitable container. OIL FILLER CAP 2. Reinstall the drain bolt and sealing washer. Tighten the plug securely. pGiz/ Improper disposal of engine oil can be harmful to the environment. If you change you own oil, please dispose of the used oil properly. Put it in a sealed container, and take it to a recycling center. Do not discard it in a trash bin or dump it on the ground. 3. Fill with the recommended oil to the top of the oil filler neck (see page 35). Engine oil capacity: 0.6 US qt (0.6 C) riG?iEq Using nondetergent oil can shorten the engine’s service life, and using 2-stroke oil can damage the engine. 4. Screw in the oil filler cap/dipstick securely. OIL FILLER/DIPSTICK CAP TOPOFOIL / P FILLER NECK Engine Oil Recommendations . Oil is a major factor affecting performance and service life. Use 4-stroke automotive detergent oil. AMBIENT TEMPERATURE SAE 1 OW-30 is recommended for general use. Other viscosities shown in the chart may be used when the average temperature in your area is within the recommended range. The SAE oil viscosity and service classification are in the API label on the oil container. Honda recommends that you use API SERVICE category SH or SJ oil with the ILSAC “starburst” certification mark displayed on the container. MAINTENANCE Air Cleaner Service A dirty air filter will restrict air flow to the carburetor, reducing engine performance. If you operate the pump in very dusty areas, clean the air filter more often than specified in the MAINTENANCE SCHEDULE. 1 NOTICE 1 Operating the engine without an air filter, or with a damaged air filter, will allow dirt to enter the engine, causing rapid engine wear. This type of damage is not covered by the Distributor’s Limited Warranty. 1. Unscrew the outer wing nut and remove the air cleaner cover. 2. Remove the inner wing nut and both air filter elements. 3. Separate both air filter elements and carefully check them for holes or tears and replace as necessary. OUTER WING NUT AIR CLEANER COVER - INNER WING NUT \ FOAM FILTER s\ ILLIIwA!~~ER MAINTENANCE 4. Clean the filters. Paper element: Tap the element lightly several times on a hard surface to remove excess dirt, or blow compressed air [not exceeding 30 psi (207 kPa)] through the filter element from the inside out. Never try to brush the dirt off; brushing will force dirt into the paper fibers. Replace the paper element if it is excessively dirty or damaged. Foam element cleaning: Wash SOLVENT the element in a solution of ENGINE OIL household detergent and warm water, then rinse thoroughly, or @$a*(, ,j wash in nonflammable solvent. db @ Allow element to dry thoroughly. Soak the element SQUEEZE 4 in clean engine oil and squeeze THOROUGHLY Ob out the excess oil. Excess oil will restrict air flow through the foam filter element and may transfer to the paper filter element, soaking and clogging it. 5. Wipe dirt from the inside of the air cleaner housing and cover. Be careful to prevent dirt from entering the air duct that leads to the carburetor. 6. Install the foam element over the paper element, and install the assembled air filter. Secure the air filter with the inner wing PAPER FILTER nut. Make sure the rubber washer is in place under the filter elements. 7. Install the air cleaner cover, and secure with the outer wing nut. AIR CLEANER HOUSING MAINTENANCE Spark Plug Service Recommended spark plugs: NGK -BPRGES DENS0 -W20EPR-U 1 NOTICE 1 Spark plugs of the wrong size or incorrect heat range can cause engine damage. For good performance, the spark plug must be properly gapped and free of deposits. Allow the engine to cool before servicing the spark plug. 1. Disconnect the spark plug cap SPARK PLUG WRENCH and remove any dirt from around the spark plug area. 2. Use a 13/l 6 in (21 mm) spark plug wrench t...
Other models in this manual:Water and Air Pumps - WDP20X (1.49 mb)