Votes - 1, Average rating: 5
(
)
)
|
manual abstract
Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 17. Do not operate tools if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate tools. SKU 40134 Page 3 18. Use proper size and type extension cord. If an extension cord is required to power tools, it must be of the proper size and type to supply the correct current to the tool without heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the tool. Most hand tools require an extension cord of 0 to 10 amps capability (up to 50 feet), with wire size rated at 18 AWG. Longer extension cords require larger size wire. If you are using the tool outdoors, use an extension cord rated for outdoor use. (signified by “WA” on the jacket). 19. Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician. Note: Performance of this product may vary depending on variations in line voltage. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the following parts are included. (2) (1) (3) (5) (6) (4) (7) (8) " ' V " V 7 6" V(; X - Z" 5"6 7[ 7$" $ 6 # (" X\X V(; ] & ^( _( !"` NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. SKU 40134 Page 4 Installation Caution: Installation should be completed by a qualified technician. Before attempting installation of the Air Horns, remove the keys from the vehicle ignition, and place wheel chocks on both sides of at least 2 wheels. Make sure engine and engine compartment is cool before beginning work. 1. Lift the vehicle hood and find a suitable location to mount the Horns and Compressor. This location must shelter the Compressor (3) and Horns (1 and 2) from incoming rain, road water, and mud from under the vehicle. It also must be away from all moving engine parts and heat. 2. Using a Screw and Nut (7), mount the Compressor (3) to the vehicle chassis in a vertical position (air outlet facing up). A hole may need to be drilled in the chassis frame to accomplish this. Before drilling hole make sure the drill’s path will not come in contact with hidden wiring or any other obstructions or vehicle components. The head of the screw slides into the Compressor mounting bracket. Securely tighten Nut. 3. Mount the Horns near the Compressor so that they are pointing forward and slightly down for maximum efficiency. The head of the screw slides into the Horn mounting bracket. Securely tighten Nut. Air outlet Compressor Nut Screw Horn Air Inlet (8) Screw Nut 4. Mount the Electric Relay (5) to the chassis frame near the Compressor using a Screw and Nut. Securely tighten. 5. Connect the Compressor to the Horns using the Vinyl Tubing (4) and the Coupling (6). Do not fold or kink tubing. To Horn Air Inlet To Horn Air Inlet Compressor SKU 40134 Page 5 6. Make the connections to the Compressor (3) and the Electric Relay (5) as shown on the Wiring Diagram. Always use vehicle terminal connectors (not supplied) on all connections. Never wrap wires around terminals as they could fall off. Connect terminal #30 on the Electric Relay (5) to a 30A fused circuit. Note: Some vehicles may employ a positive ground. If this is the case, refer to Wiring Diagram Positive Ground. Pay attention to polarity. If the Compressor turns on and the Horns do not sound, reverse the Compressor connections (+ / -). Caution: Use caution to prevent accidental short circuiting of power while performing installation. Wiring Diagram Negative Ground SKU 40134 Page 6 Wiring Diagram Positive Ground Maintenance Periodically remove the Tubing from the top of the Compressor, then add a few drops of light oil to the air outlet. Energize the unit by pressing the pushbutton. This will allow any dirt to shoot out of the air outlet. Remove yourself from the Compres- sor air outlet to avoid being hit by flying debris. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDE...