Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  
downloaded: 3   File size: 4 mb   Manafacture: Ashly  
Category: Musical Instruments
@name

Ya que las lineas seudo-balanceadas no conducen una senal verdaderamente diferencial, poseen una impedancia de linea equivalente en ambas lineas (+) y (-). Esto permite que un cable largo sea conectado desde el crossover sin comprometer al rechazo de modo comun de ruido indeseado. Para contar con un headroom maximo, termine las salidas en cargas de 600 ohms o superiores. 6.5 Salida Monoaural de Graves Los modelos XR2001, y XR4001 de Ashly cuentan con un conector jack adicional marcado como MONO

downloaded: 0   File size: 4 mb   Manafacture: Ashly  
Category: Musical Instruments
@name

El nivel maximo de entrada es de +23dBu. La “U” marcada en la posicion de las 12:00 (directamente arriba) indica “ganancia unitaria” o “unity gain” de la seccion de entrada. Recomendamos colocar este control en “unity” y controlar los niveles del sistema ya sea en las etapas anteriores al crossover o con los controles de nivel de salida. 5.3 Frecuencia de Cruce Este control infinitamente variable le permite seleccionar un punto de cruce apropiado para sus altavoces. El girar esta perilla en el s

downloaded: 40   File size: 4 mb   Manafacture: Ashly  
Category: Musical Instruments
@name

14580-9103 Tel. (716) 872-0010 Llame sin costo: (800) 828-6308 Fax: (716) 872-0739 Internet: Manual de Operacion Crossovers Electronicos XR1001, XR2001, y XR4001 Tabla de Contenido 1 INTRODUCCION .......................................................................................... 3 2 DESEMPACADO........................................................................................... 3 3 REQUERIMIENTOS DE AC.......................................................................... 4 4 CUB

downloaded: 5   File size: 1 mb   Manafacture: Ashly  
Category: Musical Instruments
@name

with a 200 ohm microphone. These outputs would be used for making a pre2. Input Pad -The input pad is a 20dB output fader recording off of the stereo mix, or attenuation switch on the rear panel for use for stacking the MX-406 with another mixer. with the XLR microphone inputs. It should 7. Aux Master Output -The 1/4" jack aux master normally be left in the "out" position for best output is used to drive a monitor or zone signal to noise ratio and should only be used amplifier, effects processor

downloaded: 2   File size: 1 mb   Manafacture: Ashly  
Category: Musical Instruments
@name

Preset names must be 20 characters or less. While working in Protea NE Software, changes to an individual preset can be saved to the ne24.24M using , or saved to the PC using . Individual preset files use the extension (*.pne). Sub Presets: Instead of saving or recalling an entire preset affecting all functions, a sub-preset affecting only a sub-set of functions may be used. To save a sub-preset, check the boxed labelled

downloaded: 1   File size: 1 mb   Manafacture: Ashly  
Category: Musical Instruments
@name

The factory default is 1kHz, but each filter is adjustable from 20Hz to 20kHz in 1Hz steps. Carefully sweeping a narrow bandwidth filter through a problem feedback area, with just a slight boost, is a quick way to find the exact frequency causing feedback trouble. Once the offensive frequency has been found, cut the filter’s level, and then adjust the bandwidth as narrow as possible while still eliminating the feedback problem. Bandwidth is adjustable from about 1/64 octave to four octaves, and

downloaded: 1   File size: 1 mb   Manafacture: Ashly  
Category: Musical Instruments
@name

For more detailed information about the proper implementation of an ethernet network, review one of the many comprehensive Ethernet networking guides available on the internet. Identify the processor in software Once the software is loaded to the computer and an Ethernet connection has been made to the NE processor, all Ashly NE products installed on that network will be automatically detected and shown in the active device listing on the left side of the Protea software startup canvas. In addit

downloaded: 2   File size: 976 kb   Manafacture: Ashly  
Category: Musical Instruments
@name

The unit should be connected to a standard 3-wire grounded electrical outlet supplying 100-240 Volts, 50-60 Hz. To reduce the risk of ground loop hum, connect all audio equipment to the same electrical power source. Removal of the ground pin is both unlawful and dangerous, as a potential shock hazard could result. Overall power consumption is less than 30 watts. NOTE: The power switch does NOT isolate the appliance from mains. Make sure the mains power socket or an alternative disconnect device

downloaded: 0   File size: 857 kb   Manafacture: Ashly  
Category: Musical Instruments
@name

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 AC POWER REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4 SECURITY COVERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5 CONTROLS . . . . .

downloaded: 10   File size: 289 kb   Manafacture: Ashly  
Category: Musical Instruments
@name

Each output channel shall include: a routing stage allowing the user to assign the output to any or a combination of input(s); a high pass/ low pass crossover filter stage with selectable slopes of 12, 18, 24 and 48dB per octave using Linkwitz-Riley, Bessel or Butterworth filter configurations; four filter stages configurable to be a parametric filter with a frequency range of 19.7Hz to 21.9KHz, 1/24th octave step and a +15dB boost, -40dB cut, or a 6 or 12dB/octave high or low shelf filter; a de





Category