Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
If you sell the unit to another user, be sure that they also receive this instruction booklet. • Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture. • This product is intended for indoor use only! • To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable materials close to the unit while operating. • The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are blocked. • Always disconnect from power source before servicing or replacing lamp or fuse and be sure to replace with same lamp source. • Secure unit to fastening device using a safety chain. • Maximum ambient temperature (Ta) is 95°F (35°C). Do not operate unit at temperatures higher than this. • In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts. • Don’t connect the device to a dimmer pack. • Make sure the power cord is never crimped or damaged. • Never disconnect the power cord by pulling or tugging on the cord. • Avoid direct eye exposure to the light source while it is on. • Do not daisy chain power to more than 4 units. Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact CHAUVET at: 954-929-1115. Text Box: Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product. 2. Introduction Features • Pre-programmed foot controller • Foot controller powered through included relay pack • 4 channels with on/off switches • Four chase options: a) 16 pattern sound activation with sensitivity adjustment b) Adjustable timed chase c) Full on override d) Blackout override • Manual override available for all control options • Includes 1 relay pack with 8 sockets (2 sockets per channel) and SF-EXCB linking cable • Additional linkable relay packs available (max 4 units, model: SR-8) • Additional power output for daisy chaining packs together Product Overview Rounded Rectangular Callout: FULL ON Turn on all outputs on the relay pack. FULL ON Turn on all outputs on the relay pack. SOUND CHASE Activates the sound active chaseAUTO CHASE Activates the auto run chase BLACKOUT Will shut all lights off PEDAL SWITCH Each pedal will turn on or off power to devices connected SPEED CONTROL SOUND SENSITIVITY CONTROL Built-in Mic. LINK OUT HANGING BRACKET POWER INPUT LINK IN Connects to Foot SwitchRESETTABLE CIRCUIT BREAKER AC VOLTAGE SWITCH 120V/230V LINK OUT Provides connection to an optional second SR8 relay pack POWER OUTLET 2 outlets per channel POWER OUTLET Always On Power IndicatorFULL ON Turn on all outputs on the relay pack. SOUND CHASE Activates the sound active chaseAUTO CHASE Activates the auto run chase BLACKOUT Will shut all lights off PEDAL SWITCH Each pedal will turn on or off power to devices connected SPEED CONTROL SOUND SENSITIVITY CONTROL Built-in Mic. LINK OUT HANGING BRACKET POWER INPUT LINK IN Connects to Foot SwitchRESETTABLE CIRCUIT BREAKER AC VOLTAGE SWITCH 120V/230V LINK OUT Provides connection to an optional second SR8 relay pack POWER OUTLET 2 outlets per channel POWER OUTLET Always On Power Indicator 3. Setup AC Power Warning! Verify that the power requirement label on your unit matches the line voltage applied. All fixtures must be connected to circuits with a suitable Earth Ground. • To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixture’s specifications chart. • A fixture’s listed current rating is its average current draw under normal conditions. • All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch. • Before applying power to a fixture, check that the source voltage matches the fixture’s requirement. • All fixtures must be connected to circuits with a suitable Earth Ground. Power Cable Configuration CABLE Pin International Screw Color BROWN Live L Yellow or Brass BLUE Neutral N Silver YELLOW/GREEN Earth EG (Ground) Green Mounting Orientation This power relay-pack can be mounted on a truss using a clamp in any position or against a flat surface using the screw holes Rigging The relay pack includes (3) clamp mounting holes for convenience of placement. You only need to use one to adhere to a truss or light stand. You must supply your own clamp and make sure the clamp is capable o...