Votes - 0, Average rating: 0
(
)
)
|
manual abstract
xz High Sound Side Low Sound Side Accidental Tone Side Resonators 12 2 1 First, place the high sound side onto the corre- sponding resonator holders. To engage the low sound side, lift it over the resonator holders and then insert it into the gap between the two holders, as shown in the illustration. Resonator Holders Resonator Holders ASSEMBLY: YV-3910/3710/3700 b Set the tone bars. 5-1 (Refer to the illustration of step 3-3 ) Raise the pedal until the knurled part is fully retracted, and fix the center rod by tightening the center rod fixing bolt. 5-2 Engage the rail clamp on rail (2) and rail (3) with rail (1) and rail (4), respectively. Rail (3) Rail (4) Rail Clamp Hold the pedal depressed to keep the sustain damper lowered, and then carefully set the tone bars. Align each tone bar individually, and hook its string onto the corresponding post. Confirm that all strings are secured to their posts, and then hook the two springs at the low sound side into each other. Low Sound Side High Sound Side Rail Clamp Rail (1) Rail (2) 5-3 Springs ASSEMBLY: YV-3910/3710/3700 n Attach the driver. 6-1 Loosen the fixing bolts at the bottom of rails (2) and (3) on the high sound side, and slide both fittings in the direction of the low sound side. 6-2 Fully insert the driver mount into the support fitting. Bottom View6-1 Insert mount until it stops Driver Support Fitting PulleyFittings Fixing Bolts Motor Unit Loosen the fixing bolts. Slide the fittings. Rail (3) Rail (2) Support Fitting 6-2 6-3 Slide the fittings moved in step 6-1 back in the direction of the high sound side. Engage the two side mounts on the driver securely with the fittings, and then tighten the fixing bolts to fasten the driver. * Set the driver so that the pulleys on either side are positioned directly below the fan side pulleys. Bottom View Fitting Fixing BoltsTighten fixing bolts. Fitting Fitting ASSEMBLY: YV-3910/3710/3700 m Attach the controller. 7-1 l YV-3910/3710 : Loosen the fixing bolt, slide out the controller hanger and hang the controller on the hanger. Return the controller hanger to its proper position and tighten the fixing bolt. . YV-3700 : There are two controller mounting pins on the high sound side of rail (1). Align the two holes in the controller mounts with these pins and hook the controller onto the pins one side at a time. l YV-3910/3710 l YV-3700 High Sound Side Controller mounting pins Controller High Sound Side ControllerController hunger Fixing bolt , Connect the driver with the controller. 8-1 Connect the MOTOR IN terminal of the driver with the MOTOR OUT terminal of the controller using the supplied 8P DIN cable*. To connect align the arrow mark ( ) on the plug with the screw next to the jack. Controller Driver Arrow Mark Screw Screw Arrow Mark 8P DIN Cable * In case the 8P DIN cable is misplaced, the following spare part may be ordered: Part No. Part Name Specification W5128092 8P DIN Cable L=220 ASSEMBLY: YV-3910/3710/3700 . Set the synchro belts (fan belts)*. 9-1 First, wrap the synchro belt around the driver pulley and then carefully slide it over the fan side pulley. * Note For Service Personnel If the belt cannot be mounted because the distance between pulleys is too wide, or the belt slips due to a too narrow pulley distance, loosen the two driver positioning screws (see illustration below) to adjust the pulley distance (belt tension). Tighten the screws securely after adjustment. Driver Side Pulley Synchro Belt (Fan Belt) Driver Positioning Screws Fan Side Synchro Belt (Fan Belt) * Slide belt over the pulley. Pulley * In case the belt is misplaced or worn, the following spare part may be ordered: Part No. Part Name Specification W5128092 Synchro Belt 18OTN15-3.0 ASSEMBLY: YV-3910/3710/3700 U0 ADJUSTMENTS 10-1 Pedal Stroke Adjustment Loosen the center rod fixing bolts to adjust the protruding length of the center rod to the desired pedal stroke, and retighten the bolts. The recommended stroke (distance between pedal and floor) Floor is 9/16" to 13/16" (1.5 to 2 cm). Pedal 9/16" ~ 13/16" (1.5 ~ 2 cm) 10-2 Wire Clip Adjustment For shipment the wire clip is initially set at a low position for packing reasons. For normal use this clip should be adjusted as follows: With the pedal released loosen the fixing bolt of the wire clip, shift the clip up until distance A in the illustration below is 1/16" to 1/8" (1 to 3 mm), and tighten the wing bold in this position. The clip also allows setting the instrument to "half sustain damper" (slight continuous damper effect) or "open damper"* by changing its position accord...
Other models in this manual:Musical Instruments - YV-2700G (434.67 kb)
Musical Instruments - YV-3710 (434.67 kb)
Musical Instruments - YV-3710M (434.67 kb)
Musical Instruments - YV-3910 (434.67 kb)