Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
• Always keep the total speaker impedance at or above the rated load. • Unplug the amplifier before cleaning it. NEVER spray liquid cleaners onto the amplifier. Wipe it with a slightly dampened, lint-free cloth to remove dirt and film. • Do not use the amplifier if it has sustained damage to the chassis, controls, or power cord. Refer the unit to an authorized service center for inspection. • Amplifiers capable of producing high volume levels are also capable of inflicting permanent hearing loss or damage, if the exposure to such levels is prolonged. Such damage is progressive and irreversible! THIS EQUIPMENT HAS BEEN DESIGNED AND ENGINEERED AND RELIABLE OPERATION. IN ORDER TO PROLONG THE LIFE OF THE UNIT AND PREVENT ACCIDENTAL DAMAGES OR INJUR GUIDELINES: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OR REMOVE THE GROUND PIN OF THE POWER CORD; CONNECT ONLY TO A PROPERLY GROUNDED WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT THIS EQUIPMENT TO RAIN OR MOISTURE. CAUTION: NO USER-SERVICEABLE PARTS INSIDE. REFER SER VICE PERSONNEL. CAUTION: OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMP AND EAR PROTECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. "IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL" “ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.” "REFERREZ-VOUS AU MANUAL D'UTILISATION" "UNBEDINGT IN DER BEDIENUNGSANLEITUNG NACHSCHLAGEN" EXPLANATION OF GRAPHICAL SYMBOLS: EXPLICACION DE SIMBOLOS GRAFICOS: EXPLICATION DES SYMBOLES GRAPHIQUES: "GEFAHLICHE SPANNUNG" = = ATTENTION RISQUE D'ELECTROCUTION NE PAS OUVRIR ATTENTION: POUR REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE. VORSICHT ELEKTRISCHE SCHLAGGEFAHR NICHT OFFENEN VORSICHT: ZUR MINIMIERUNG ELEKTRISCHER SCHLAGGEFAHR NICHT DEN DECKEL ABENHMEN. INTERNE TEILE KONNEN NICHT VOM BENUTZER GEWARTET WERDEN. DIE WARTUNG IS QUALIFIZIERTEM WARTUNGSPERSONAL ZU UBERLASSEN. BA-110 BASS AMPLIFIER BA-110 BASS AMPLIFIER TOP PANEL: 0dB0dB -15dB-15dB Input ContourContour HeadphonesHeadphonesLine OutLine Out PowerCD InputCD Input OnOn Volume Low Mid High 0 10 54 3 2 1 9 8 7 6 0 10 54 3 2 1 9 8 7 6 0 10 54 3 2 1 9 8 7 6 0 10 54 3 2 1 9 8 7 6 12345 6 1. 0dB INPUT: Connect your “passive” bass guitar here by means of a shielded instrument cable. This input is not padded and is best suited for basses without active electronics or “hot” pickups. 2. -15dB INPUT: Connect your “active” bass here by means of a shielded instrument cable. This input is padded 15dB and is best suited for basses with active electronics and/or “hot” pickups. 3. VOLUME: Use this control in conjunction with your instrument’s volume controls to adjust the output level of the amplifier. The BA-110 employs a built in limiter to keep the output clean at full power, however, extreme settings may cause some audible distortion. 4. CONTOUR: This switch, when depressed, boosts the high and low frequencies while cutting the midrange to provide a “funk” slap-bass tone. 5. LOW: Use this control to adjust the low frequency level of the amplifier. This control has a 28dB range at 100Hz. 6. MID: Use this control to adjust the midrange level of the amplifier. This control has a 26dB range at 600Hz. 7. HIGH: Use this control to adjust the high frequency level of the amplifier. This control has a 35dB range at 10kHz. 8. CD INPUT: Use these RCA jacks to connect the line level (or headphones) output of 7 8 9 1011 a CD player or tape deck. The two jacks sum the stereo signal into a mono signal which is fed into the BA-110 just prior to its power amplifier. Use the volume control on the CD or tape player to control the level of this signal. 9. LINE OUT: This jack supplies a post-eq, unbalanced line level signal for connecting to a house sound board, recording unit or external amplifier. The level of this signal is controlled by the Volume control (#3). 10. HEADPHONES: For private practice sessions, plug headphones into this jack. The internal speaker is disconnected when the headphones jack is used. 11. ON LED: This LED illuminates when the amplifier is plugged in and turned on. 12. POWER: Use this switch to turn the amplifier on and off – the top of the switch is depressed in the on position. 13. POWER CORD (rear panel, not shown): Use this cord to connect the amplifier to a suitable source of A.C. voltage. This is a grounded, three-wire cord and must be connected to a properly grounded outlet. DO NOT attempt to defeat the ground connection of the power cord! If your amp was purchased outside of the United States, see the sticker next to the A.C. connector f...