Votes - 3, Average rating: 3
(
)
)
|
Other manuals for this model:
manual abstract
“Advanced Settings” Dialog Box The parameters in the “Advanced Settings” dialog box set up the DME-N Network Driver for automatic device detection, and allow saving and loading setup files. Auto Detect Allows automatic detection of connected devices. A maximum of 254 addresses (***.***.***.1 through ***.***.***.254) can be detected. NOTE Only MAC addresses of devices on the same subnet as the computer can be detected. Before searching for MAC addresses make sure that the computer is connected to the subnet to be searched, and that an appropriate IP address is assigned. .. Detect from Specifies the start IP address for automatic detection. .. Detect to Specifies the end IP address for automatic detection. .. [Start] Button Initiates automatic detection, and causes the detected device list (..) to be updated accordingly. This button is grayed out and is not accessible during automatic detection. .. [Abort] Button Aborts automatic detection. This button is grayed out when automatic detection is not in progress. .. Currently searching Displays the IP address being checked during automatic detection. No display when automatic detection is not in progress. .. .. .. .. .. .. .. .. .. .. DME-N Network Driver Installation Guide for M7CL/LS9/DSP5D 9 .. Detected Device List This list shows all detected devices. No devices will be displayed initially. [Add] Checkbox Checked devices will be added to the Target Device List when the [Add to Device List] button (below) is clicked. Devices that are already registered cannot be checked. Device IP Address The IP address of the corresponding detected device. Device Name If a name has been registered for the detected device it will be displayed here, otherwise no name will be displayed. Device MAC Address The MAC address of the corresponding detected device. .. [Add to Device List] Button Devices with checked [Add] checkboxes will be added to the Target Device List when this button is clicked. .. [Cancel] Button Closes the dialog box without making any changes. .. [Import Setup from File] Button When working in a different environment it is possible to load a previously saved setup file. Click to open the “Open existing file” dialog box. Select a setup file and then click the [Open] button to import the corresponding settings. .. [Export Setup to File] Button It is possible to save the setup data to a file that can then be reloaded when working in a different environment. Click to open the “Saves the current file with a new name” dialog box. Enter a file name and click the [Save] button to save the setup file. TCP/IP Setting s Windows XP 1 Access the Control Panel. 2 If the control panel appears as category view, click [Switch to Classic View]. 3 Double-click [Network Connections] . [Local Area Connection]. The “Local Area Connection Status” dialog box will be displayed. NOTE If the “Local Area Connection properties” dialog box appears, skip ahead to step 5. 4 Click [Properties]. The “Local Area Connection Properties” dialog box will be displayed. 5 Select [Internet Protocol (TCP/IP)], then click [Properties]. The “Internet Protocol (TCP/IP) Properties” dialog box will be displayed. 6 Click [Use the following IP address]. 7 Enter your computer’s IP address into [IP address], the Gateway’s IP address into [Default gateway], and “255.255.255.0” into [Subnet mask]. NOTE When installing on the same subnet as the DME unit(s), set the gateway’s host address to 254. NOTE It is recommended that you set the IP address to “192.168.0.3” when peer-to-peer connecting a single device to a computer. For details on settings when connecting to multiple devices via a switching hub, refer to the installation guide for each editor software. 8 Click [OK]. 9 Restart your computer. DME-N Network Driver Installation Guide for M7CL/LS9/DSP5D Windows Vista / 7 / 8 1 Access the Control Panel, then click or double-click [Network and Sharing Center] or [View network status and tasks]. The “Network and Sharing Center” is displayed. 2 Click [Manage network connection] or [Change adapter settings] from the “Tasks” list located in the left side of “Network and Shareing Center” window, then double-click [Local Area Connection]. The “Local Area Connection Status” dialog box will be displayed. NOTE The “User Account Control” dialog box may appear. Click [Continue]. NOTE If the “Local Area Connection properties” dialog box appears, skip ahead to step 4. 3 Click [Properties]. The “Local Area Connection properties” dialog box will be displayed. NOTE The “User Account Control” dialog box may appe...
Other models in this manual:Musical Instruments - DSP5D (713.21 kb)
Musical Instruments - LS9-32 (713.21 kb)
Musical Instruments - M7CL-32 (713.21 kb)
Musical Instruments - M7CL-48 (713.21 kb)