Votes - 4, Average rating: 4.8 ( )

Manafacture: Yamaha File size: 1.59 mb File name: Language of manual:

Photos and specs  Yamaha  AX-396

Other manuals for this model:

Musical Instruments - AX-396 (276.2 kb)

If this unit fails to turn on when the POWER switch is pressed: The IMPEDANCE SELECTOR switch may not be set to either end. If so, set the switch to either end when this unit’s power supply is completely cut off. Select the position whose requirements your speaker system meets. A OR B : 6WMIN. /SPEAKER A B : I2WMIN. /SPEAKER A OR B : 4WMIN. /SPEAKER A B : 8WMIN. /SPEAKER (Right position) If you use one pair of speakers, the impedance of each speaker must be 4W or higher. If you use two pairs of speakers, the impedance of each speaker must be 8W or higher. (Left position) If you use one pair of speakers, the impedance of each speaker must be 6W or higher. If you use two pairs of speakers, the impedance of each speaker must be 12W or higher. 2 AC OUTLET(S) (SWITCHED) * (Europe, China and General models) ...................................................... 3 SWITCHED OUTLETS (U.K. and Australia models) ............. 1 SWITCHED OUTLET Use these to connect the power cords of your components to this unit. The power to the SWITCHED outlets is controlled by this unit’s POWER or STANDBY/ON switch. These outlets will supply power to any connected unit whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLETS is 100W. *3 GND terminal (For turntable use) Connecting the ground wire of the turntable to the GND terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected. E-5 CONTROLS AND THEIR FUNCTIONSCONTROLS AND THEIR FUNCTIONS FRONT PANEL AX-496 123 457 NATURAL SOUND STEREO AMPLIFIER AX–496 VOLUME l6 20 28 40 60 l2 8 4 2 0 –dB PHONES BASS 5 5 4 3 2 l 0 l 2 4 TREBLE 5 5 4 2 l 0 l 2 3 4 BALANCE 5 5 4 3 2 l 0 l 2 3 4 L R SPEAKERS A ON OFF B STANDBY/ON POWER ON OFF STANDBY INPUT PURE DIRECT CD/DVD DIRECT AMPAUX PHONOTUNERCD/DVDTAPEMD LOUDNESS 5 7 4 3 2 l FLAT I0 —30dB 9 8 REC OUT CD/DVD TUNER PHONO TAPE MD AUX 8 90 A BCDEF G AX-396 123 467 NATURAL SOUND STEREO AMPLIFIER AX–396 VOLUME l6 20 28 40 60 l2 8 4 2 0 –dB PHONES BASS 5 5 4 3 2 l 0 l 2 4 TREBLE 5 5 4 2 l 0 l 2 3 4 BALANCE 5 5 4 3 2 l 0 l 2 3 4 L R SPEAKERS A ON OFF B STANDBY/ON POWER ON OFF STANDBY INPUT TAPE MONITOR CD/DVD DIRECT AMPAUX PHONOTUNERCD/DVDTAPEMD LOUDNESS 5 7 4 3 2 l FLAT I0 —30dB 9 8 890ABC EF G EnglishEnglish 1 POWER Press this switch inward (ON) to use this unit. In this state, you can turn on this unit or turn this unit in the standby mode by pressing STANDBY/ON. Press this switch to release it outward (OFF) to completely cut off this unit’s power supply from the AC line. 2 STANDBY indicator Lights up only while this unit is in the standby mode. 3 STANDBY/ON Press this switch to turn on the power. Press again to set this unit in the standby mode. * This switch can be used only when POWER is set in the ON position. Standby mode This unit is still using a small amount of power in this mode in order to be ready to receive infrared-signals from the remote control. 4 Input source indicators The indicator of the currently selected input source lights up. 5 PURE DIRECT and indicator Press this switch, and the indicator above it lights up. You can listen to a source in the purest sound with this function. (Refer to page 12 for details.) Press this switch again to cancel this function. AX-496 only 6 TAPE MONITOR and indicator Press this switch to turn on the indicator above it. You can listen to the sound played on the tape deck connected to the TAPE terminals on the rear of this unit. When the tape deck is used for recording, you can also monitor the sound being recorded. AX-396 only * To listen to the source selected with the INPUT selector, press this switch again to turn off the indicator. * When this function is on (the indicator is illuminated), the tape deck (TAPE) cannot be selected with the INPUT selector. * When the tape deck (TAPE) is selected with the INPUT selector, this function will not turn on even if TAPE MONITOR is pressed. 7 CD/DVD DIRECT AMP and indicator Press this switch, and the indicator above it lights up. You can listen to a CD or DVD source in the purest sound with this function. (Refer to page 12 for details.) Press this switch again to cancel this function. 8 Remote control sensor Receives signals from the remote control. PHONES 9 PHONES jack When you listen with headphones, connect the headphones to the PHONES jack and set both SPEAKERS A and B switches to the OFF position. 0 SPEAKERS Press the switch A or B (or both) inward (ON) for the speakers you will use. Press and release the switch outward (OFF) for the speakers you do not use. A Tone controls BASS Rotate this knob to increase or decrease the low frequency response. The 0 position produces a flat response. TREBLE Rotate this knob to increase or decrease the high frequency response. The 0 position produces a flat response. B BALANCE The balance of the output volume to the left and right speakers can be adjusted to compensate for ...

Download now

Please, enter two numbers from picture: