Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Press it again to switch the power off. * Standby mode While the power is on, pressing the POWER key on the remote control transmitter switches the unit to the standby mode. (In this mode, the power indicator is half illuminated.) 2Power indicator Lights up while the power is on. 3Remote control sensor Receives signals from the remote control transmitter. 4PURE DIRECT switch and indicator Press this switch so that the indicator lights up to listen to an audio source in the purest sound. (Refer to page 12 for details.) CDEF G 5INPUT selector Selects a program source to listen to. 6VOLUME control Used to raise or lower the volume level. * When the volume is decreased by pressing the MUTING key on the remote control transmitter, the indicator on the VOLUME control flashes on and off. PHONES 7PHONES jack When you listen with headphones, connect the headphones to the PHONES jack. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position. 8SPEAKERS switches Set the switch A or B (or both A and B) for the speaker system (connected to this unit) you will use to the ON position. Set the switch for the speaker system you will not use to the OFF position. English 9 BASS control Used to increase or decrease the low frequency response. The DEFEAT position produces flat response. 0 TURNOVER FREQUENCY switches Used to adjust the turnover point of the BASS and TREBLE controls respectively. This gives you flexible control over bass and treble response characteristics. A TREBLE control Used to increase or decrease the high frequency response. The DEFEAT position produces flat response. B SUBSONIC FILTER switch Used to cut out undesirable ultra-low-frequency signals caused by turntable rumble or warped records without losing sound quality. C MODE switch This switch can be used for switching between stereo and monaural operation. Normally this switch should be set to the STEREO position. D BALANCE control Adjusts the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. E Continuously variable LOUDNESS control Used to compensate for the human ears’ loss of sensitivity to high and low-frequency ranges at low volume. F REC OUT selector This switch can be used to select a program source and supply that source directly to the REC OUT terminals on the rear panel, independently of the setting of the INPUT selector. This function allows you to record the selected program source while listening to another program source. G PHONO (MM/MC) switch This switch can be used to select either the MM (moving magnet) or MC (moving coil) position to match the phono cartridge used. (Refer to page 12 for details.) REMOTE CONTROL TRANSMITTER The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the CD player, tuner, tape deck and turntable connected to this unit are YAMAHA components designed for remote control compatibility, then this remote control transmitter will also control various functions of each component. 132YAMAHA HIFI SYSTEM REMOTE CONTROL TRANSMITTER TAPE 2 POWER VOLUME AUX – MUTING TAPE 1 TUNER CD PHONO TAPE 3 PLAY For Control of This Unit 1 Input selector keys Selects input source. 2 MUTING key When pressed, decreases the volume level by 20 dB. To resume original volume level, press this again. While muting, the indicator on the VOLUME control flashes on and off continuously. 3 VOLUME +/– keys Turns the volume level up/down. 4 POWER key 1 Turns the power on/off. * While the power is on, pressing the POWER key on the remote control transmitter switches the unit from the power-on mode to the standby mode, and vice versa. (In 4 the standby mode, the power indicator on the front panel is 2 half illuminated.) 3 4 For Other Component Control Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their functions will be the same. On each key function, refer to the corresponding instruction on your component’s manual. 1 Tape deck keys Controls tape deck. DIR A, B and A/B are applicable only to double * cassette tape deck. For a single cassette deck with automatic reverse * function, pressing DIR A will reverse the direction of tape running. 2 Tuner keys Controls tuner. +: Selects higher preset station number. –: Selects lower preset station number. A/B/C/D/E: Selects the group (A – E) of preset station numbers. 3 CD player keys Controls compact disc player. DISC is applicable only to compact disc changer. * 4 Turntable key Starts/stops record play on turntable. TAPE 3 TAPE 2 AUX TAPE 1 CD TUNER PHONOPURE DIRECT MONO STEREO TREBLE BALANCE 4 3 2 l DEFEAT l 2 3 4 LOUDNESS 5 5 4 3 2 l 0 l 2 3 4 L R 5 7 4 3 2 l FLAT 10 9 8 6 –40dB REC OUT AUX 1/2 CD TUNER PHONO 2/3TAPE COPY 1 3 SUBSONIC FILTER MODE PHONO MC MM EnglishOPERATIONS EnglishOPERATIONS POWER 2 PHONES SPEAKERS BASS TURNOVER FRE...