Votes - 2, Average rating: 4.5
(
)
)
|
Other manuals for this model:
manual abstract
These speakers feature a magnetically shielded design, but there is still a chance that placing them too close to a TV or a computer monitor might impair picture color. Should this happen, move the speakers away from the TV or the computer monitor. Unpacking After unpacking, check that the following parts are included. . Satellite speaker x 5 . Accessories . Speaker cable (3m) x 3 . Speaker cable (7m) x 2 . Cable holder x 1 . Pad x 20 . Fastener x 1 This speaker package is designed to be suitable for use in a home theater sound system. The included five full-range satellite speakers are all the same models. When using these speakers in a home theater sound system, assign them to two front speakers, one center speaker and two rear speakers respectively. Recommended speaker placement Before making connections, place all speakers in their respective positions. The positioning of the speakers is important because it controls the overall sound quality of your audio system. Place the speakers depending on your listening position by following the instructions below. * The speakers can be mounted on a wall. (See the next page.) Front speakers: On both sides of and at approximately the same height as the TV (or computer monitor). Rear speakers: Behind your listening position or on both sides of the listening room. Normally, set the rear speakers at positions higher than your ears when you sit at the listening position. Center speaker: Precisely between the front speakers. * When mounting the center speaker on the monitor, see the next page. . Adjusting the front angle of the speakers The front angle of the speakers can be adjusted as shown below. 1 Loosen the screw on the bottom of the speaker stand. * Attach the supplied nonskid pads at the four corners on the bottom of the stand to prevent the speaker from moving by vibrations. Pads 2 Adjust the speaker angle on the stand as you prefer, and then tighten the screw. E-1 . Mounting the speakers on a wall The speakers can also be hung on the wall. Fasten screws into a firm wall or wall support as shown in the figure, and hang the slits on the rear of the speaker on the protruding screws. * Make sure that the screws are securely caught by the slits. Tapping screw (4 mm) (Available in hardware stores) 50 mm Min. 20 mm 4 mm Wall/ wallsupport Warning . Each speaker weighs 0.3 kg (0.6 lbs.). Do not mount them on thin plywood or a wall with soft surface material. If mounted, the screws may come out of the flimsy surface and the speakers may fall. This could damage the speakers and cause personal injury. . Do not install the speakers on a wall with nails, adhesives, or any other unstable hardware. Long-term use and vibrations may cause them to fall. . To avoid accidents resulting from tripping over loose speaker cables, fix them to the wall. . Placing the center speaker on top of the monitor A speaker used for the center speaker can be placed on top of the monitor. Follow one of the two procedures below for placing a speaker on top of the monitor. Placing the center speaker on top of the monitor by using the provided fastener First remove the stand from the speaker, and attach the provided fastener at the bottom of the speaker and on top of the monitor to prevent the speaker from falling. * This is the recommended method for placing a speaker on top of the monitor. If discoloration of picture occurs, or you need the speaker stand to adjust the speaker angle on top of the monitor, you can select the following method. Fastener Note Do not place the speaker on top of the monitor with an inclination of more than 10 degrees. 10. 10. Placing the center speaker on top of the monitor with the speaker stand attached to the speaker In this method, you need to fix the speaker cable on the monitor by using the provided cable holder to prevent the speaker from falling. 1 Remove the backing sheet from the holder, and attach the holder on top of the monitor by pressing it down forcibly. (The top of the monitor must be cleaned beforehand.) Cable holder 2Tie the speaker cable to the holder firmly with a provided vinyl-coated wire (which is originally used for bundling the speaker cables) as shown below. Vinyl-coated wire Note Though this speaker is a magnetically shielded type, there may be some influence on the monitor picture depending on the type of monitor or the placement of the speaker. In such a case, place the speaker further apart from the monitor until there is no influence on the monitor picture. E-2 Connection to your amplifier Specifications Connection to your amplifier Specifications English (See the figure inside the front cover.) Before making connections, make sure that the amplifier is switched off. Notes on connections . Connect the push-type input terminals at the rear of the speakers to the speaker output terminals of your amplifier with the provided speaker cables. . One side of the speaker cable has a white broken line. Connect the (+) terminals on both the amplifier a...