Votes - 2, Average rating: 3.5
(
)
)
|
Photos and specs Yamaha DVX-S100 |
manual abstract
Select the appropriate position for each speaker based on the size of the speakers in your configuration. 62 – 63 A “humming” sound can be heard. Incorrect cable connections. Firmly connect the audio plugs. If the problem persists, the cables may be defective. 14 – 15 The volume level cannot be increased, or the sound is distorted. The component connected to the OUT (Rec) jacks of this unit is turned off. Turn on the power to the component. — The sound effect cannot be recorded. It is not possible to record the sound effect by a recording component. — A source cannot be recorded by a digital recording component connected to the DIGITAL OUTPUT jack of this unit. A source component is not connected to the DIGITAL INPUT jacks of this unit. Connect the source component to the DIGITAL INPUT jacks of this unit. 14 – 15 This unit does not operate properly. The internal microcomputer has been frozen by an external electric shock (such as lightning or excessive static electricity) or by a power supply with low voltage. Disconnect the AC power cord from the outlet and then plug it in again after about 30 seconds. — There is noise interference from digital or high- frequency equipment, or this unit. This unit is too close to the digital or high- frequency equipment. Move this unit further away from such equipment. — TROUBLESHOOTING ¦ Disc playback Problem Cause Remedy Refer to page No response when buttons pressed. Some operations may be prohibited by the disc. — Playback does not start. The disc is damaged. Check the disc carefully; replace it if necessary. — There is moisture on the laser pickup. Wait 1 to 2 hours after switching the unit on before trying to play a disc. — The disc has been loaded upside down. Reload the disc with the label side facing up. — The disc is dirty. Clean the disc. 30 Alternative languages fail to be selected. An alternative language is not selected with discs which do not contain more than one language. — In the case of some discs, the alternative language cannot be selected with “Audio” or “Subtitle”. Try selecting it from the disc’s menu if one is available. — No subtitles. The disc does not have subtitles. — Subtitle is turned off. Show subtitles by pressing SUBTITLE or using on-screen menu. 35 Angle cannot be changed. The disc or the scene being played does not support multi-angle. — No sound. Distorted sound. If the “D.MIX” indicator on the front panel display goes out while playing a multichannel DVD-Audio disc, sound will only be output from speakers specified by the disc. — Sound “skips”. The disc is dirty. Clean the disc. 30 Noise from inside of the unit. The disc may be warped. Replace the disc. — Picture distorted during SEARCH. Some distortion is normal during SEARCH. — No picture. (U.S.A. and Canada models) If you play PAL system DVD-Audio, “This disc is PAL system. The output is sound only” may appear on the monitor. Picture is not available because the disc’s video signal system is different. — Picture appears incorrectly. Incorrect “TV aspect” setting. Select the right position. However, it may be difficult to adjust many DVD-Videos’ widescreen format to fit perfectly in your 4:3 video monitor. 48 (U.S.A. and Canada models) PROGRESSIVE is turned on even though the connected monitor cannot receive the progressive signals. Turn off the PROGRESSIVE feature. 38 – 39 (U.S.A. and Canada models) Due to the editing method or material used on a DVD, ghosting may occur with progressive output. Turn off the PROGRESSIVE feature. 38 – 39 APPENDIX English 71 TROUBLESHOOTING TROUBLESHOOTING Cause Remedy Refer to page No on-screen display. Go to Display on the SETUP menu, and select “On” for “On-Screen Messages”. 49 On-Screen Menu Icons not displayed or only partially displayed on the television. Press the cursor buttons (u, d) while the rightmost icon is highlighted to change the menu bar position. 34 There is a lot of ghosting. Use the on-screen menu icons to adjust the picture quality. 37 “No Play” appears on the unit’s display. The disc that this unit cannot play is loaded. — This unit does not recognize disc (“No disc” appears on the display, or the display shows the status when no disc is loaded). The disc is not placed properly. Place the disc properly. — TROUBLESHOOTING ¦ Tuner Problem Cause Remedy Refer to page FM/ AM Previously preset stations cannot be tuned in. The preset stations are cleared. Pre-set the stations once again. 55 FM stereo reception is noisy. The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or Check the antenna connections. Try using a high-quality directional FM antenna. 16 FM the antenna input is poor. Use the manual tuning method. 54 There is distortion, and clear reception cannot be obtained even with a good FM antenna. There is multipath interference. Adjust the antenna position to eliminate multipath interference. 16 The desired station cannot be tuned in with The station is too weak. Use a high-qual...