Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
Corner!” appears in the front panel display if INSTALLED POSITION is set to ANGLE TO WALL OR CORNER (see page 55). My Surround This mode enables surround system in a small listening area which may not fulfill the listening room conditions for other beam modes (see “Before installing this unit” on page 13). Use this beam mode when you want to enjoy surround sound near this unit, or when the other beam modes are unavailable. Press MY SUR. to select My Surround. Note The front left and right sound beams are output directly toward the listening position. 3 Beam Outputs sound beams from the front left and right and center channels. This mode is ideal for enjoying movies with the whole family. Because the listening position area is widened, you can enjoy excellent quality surround sound over a wider area. In addition, you can use this mode when the listening position is close to the backside of the wall, and the surround left and right sound beams cannot be reflected off the wall. Press 3BEAM to select 3 Beam. 3BEAM Notes Beam mode settings such as beam angles and distances are ineffective in this mode. • For the full effect of My Surround, your listening position must face toward the front of this unit. MY SUR. 43 En Enjoying surround sound ■ Decoder indicators Depending on the input source and the selected surround mode, the decoder indicators in the front panel display light up as follows: y • You can select an input mode (AUTO, DTS, or ANALOG) by pressing INPUTMODE repeatedly (see page 68). • Discs encoded in DTS-ES, Dolby Digital 5.1 EX, Dolby Digital EX, or Dolby Digital Surround EX will be played back in DTS or Dolby Digital. ■ Surround modes and recommended sources Surround mode Recommended source DTS Neo:6 Cinema Movies Music Music Dolby Pro Logic - All sources Movie Movies Dolby Pro Logic II Music Music Game Games Notes * When you select an input source (see page 39), the surround mode used for the previously selected input source is automatically selected. * If the power of this unit is turned off and on again, the surround mode used for the previously selected input source before the power was turned off is automatically selected. * If the surround modes are not available, “Prohibit” appears in the front panel display when you press SUR. DECODE. * The surround modes are available: - when the beam mode is set to a setting other than the stereo playback (see page 48) and My Surround (see page 43). - when 2-channel signals are being input. Status Indicator When PCM signals are being input PCM When DTS digital signals are being input or DTS Neo:6 is selected as the surround mode «Its When Dolby Digital signals are being input □□ DIGITAL When Dolby Pro Logic is selected as the surround mode □□PL When Dolby Pro Logic II is selected as the surround mode □□PLII 44 En Enjoying surround sound Enjoying 2-channel sources in surround sound This unit can decode 2-channel sources for 5.1-channel playback so that you can enjoy a variety of surround sound effects by switching the surround mode. y The beam mode must be set to 5 Beam, Stereo plus 3 Beam, or 3 Beam (see page 42). Press SUR. DECODE repeatedly (or press SUR. DECODE and then press <| / D) to switch between surround modes. Choices: Neo:6 Cinema, Neo:6 Music, PRO LOGIC, PLII Movie, PLII Music, PLII Game Default setting: Neo:6 Cinema SUR. DECODE 1 Set the operation mode selector to YSP. [tv/AvI I yspT I 0 0 1 1 2 SUR. DECODE or m 3 l s 45 En Enjoying surround sound Enjoying TV in surround sound You can enjoy analog audio signals output from your TV in real surround sound. y Before performing the steps below, set the volume of this unit to 30. 4 If you hear sound from your TV speakers, reduce the volume level of your TV until you can no longer hear any audio being output. To reduce the TV volume level, use the remote control supplied with your TV. 5 Press VOLUME +/- to adjust the volume level. 1 Select the TV channel you want to watch. To select a TV channel, use the remote control supplied with your TV. 2 Set the operation mode selector to YSP. Itv/AVI ■ r~YSP~l" i -X 3 Press TV. This unit outputs audio signals from your TV. VOLUME 6 Press SUR. DECODE repeatedly (or press SUR. DECODE and then press <| / |>) to switch between surround modes. Signals input from 2-channel sources are played back in multi-channels. For more information on surround modes, see page 44. SUR. DECODE or SUR. DECODE 46 En Enjoying surround sound Adjusting surround mode parameters You can configure the parameters for Dolby Pro Logic II Music and DTS Neo:6 Music to fine-tune the surround sound effect. 1 Repeat steps 1 and 2 in “Enjoying 2-channel sources in surround sound” on page 45 and select PL II Music or Neo:6 Music. 2 Press ^ ^ to select the parameter. ■ When Dolby Pro Logic II Music is selected PANORAMA Gives the front left and right channel sound a wraparound effect, distributed throug...