Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
When adjusting the height or angle, do not suddenly loosen the bolt. The pad may drop, the rack or pipes may slip, pinching or causing injury to hands or fingers. Do not sit or step on the rack. The rack may overturn or be damaged resulting in injury. Please be careful when children are close to or touching the product. The product has many pipes and arms so careless movement around the product may result in injury. When setting the pads and modules, please pay close attention in regards to the handling and setting of cables. Feet may become entangled in the cables resulting in falls. Do not put your hands or feet under the foot pedal or foot switch. They may be pinched resulting in injury. Watch your fingers when adjusting clamps. They may become pinched resulting in injury. Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers. Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. Caution (including danger, or warning). This mark indicates cautions in which you should pay close attention to. Acts indicated with this icon are prohibited and should not be attempted. To prevent against accidents and injury Please follow the cautions listed below * Specifications are subject to change without notice. If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. WARNING CAUTION If this symbol is ignored and the equipment is used improperly, there is a danger of injury to persons handling the equipment, and material damage could occur. ¦ RS75 Assembly * Parts for the RS75's main structure have already been assembled before packing. After removing the unit from the box, follow the instructions described below to complete the assembly. A Phillips (+) screwdriver is required when attaching the Drum Trigger Module. Please prepare one before starting assembly. 1 After removing the unit from the box, remove all cushion material. 2 Setting up the parts • Loosen the wing bolts, slide the pipes out a little, and attach the rubber feet. • Loosen the bolts on the movable arms and legs, as shown in the diagrams below, then secure the bolts firmly once setting is complete. Follow the setup order (q~i) in the diagrams shown below. q w e ..Caution Left Leg Assembly Right Leg Assembly Module Holder Assembly ..Caution y r t u Cymbal Holder Side Arm (L) Assembly Side Arm (R) Assembly 3 Attaching the Drum Trigger Module 3-1 Remove the module holder from the holder clamp, and use the supplied screws to attach the Drum Trigger Module. Make sure only the supplied screws are used. Using any other screws may result in the unit falling off the holder or damage. Caution : Make sure the bolts marked with a " " are loosened before setting up. 3-2 Reattach the module holder to the holder clamp. INTRODUCTION Thank you for purchasing the Yamaha Electronic Drum Rack System RS75. Before using, thoroughly read these assembly instructions, and use this product safely and correctly. i Cymbal Holder ¦Inside This Package Before setup, please make sure that all of the items listed below are present and accounted for. If anything is missing, please contact the dealer from whom you purchased the unit. . Rubber Foot (x2) Rubber Foot Rubber Foot Loosen Loosen Loosen Loosen Be careful around the pipe edges. The cut pipe ends are sharp and can injure your fingers. ¦ Set up example 4 Attaching the cymbal pads Make sure all bolts on clamps, pads, etc., are firmly tightened. Loose or over-tightened bolts may result in the part falling off and/or damage. Please use caution. After assembly is complete, setup the kick pad, real hi-hat pad, etc., and connect the cables. Use the supplied cable bands to secure the cables to the frame pipes to keep cables out of the way during performance. If the rack is moved even after setup is complete, make sure the bolts are loosened before moving the rack. Attach the cymbal pads to the cymbal holders and adjust their position, then secure in place. (Please refer to the Owner's Manual that came with the cymbal pads on attaching the cymbal pads.) 5 Attaching the drum pads Attach drum pads to the hexagonal rod cylinder and adjust their position, the secure in place. Drum Trigger Module Holder Clamp Module Holder Step 3-1 Step 3-2 Step 5 Drum Pad Step 4 Printed in Indonesia WG24080 ¦Optional Parts Step 3 e q w w w y u i r Satellite Speaker Satellite Speaker PCY130S TP65S Sub Woofer amp unit PCY150S t RHH130 e PCY130 . Pad and Drum Trigger Grouping q DTX Series Drum Trigger Module w TP65/65S Drum Pad e PCY130/130S Cymbal Pad r PCY150S Cymbal Pad t RHH130 Real Hi-hat Pad y Hi-hat stand *HS740 etc. • SPAT1 Speaker Attachment • TPCL65 Tom Holder • CYAT65 Cymbal Attachment . Monitor System and Attachment Grouping • MS50DR • Sub Woofer amp unit • MS100DR • Sub Woofer amp unit u Foot Pedal FP-7210 etc. i KP65 Kick Pad • Satellite Speakers • Satellite Speakers Cymbal Pa...