Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
Before using, thoroughly read this assembly manual, and use this product safely and correctly. ■ RS100 Rack Stand Parts fA Side Assembly A (x1) * Before assembling the rack stand, make sure all of the parts shown below are included. B Side Assembly B (x1) 0 Center Pipe Assembly A (x1) E Center Pipe Assembly B (x1) G Tom Holder (x5) Module Holder (x1) (4 screws included) И Cymbal Holder (x2) ■Q№^g3t= E Cable Band (x10) M Tuning Key (x1) C Side Assembly C (x1) Side Arm (x1) HD Module Holder Clamp (x1) I Felt Washer (x2) [N Assembly Instruction (this sheet) PRECAUTIONS Before using, please read this “Assembly Instruction” sheet, and use this product in a safe and proper manner. Especially for children, parents or an instructor should teach the children the proper manner in which to use the device. To prevent against accidents and injury Please follow the cautions listed below A Caution (including danger, or warning). This mark indicates cautions in which you should pay close attention to. 0Acts indicated with this icon are prohibited and should not be attempted. This icon indicates acts that you are urged to follow. If this symbol is ignored and the equipment is used improperly, fatal injury to persons or se-WARNING rious damage could occur. A Always set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the instrument being unstable and overturning. A Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury. 0 When adjusting the height or angle, do not suddenly loosen the bolt. The pad may drop, the rack or pipes may slip, pinching or causing injury to hands or fingers. 0 Do not sit or step on the rack. The rack may overturn or be damaged resulting in injury. A Please be careful when children are close to or touching the product. The product has many pipes and arms so careless movement around the product may result in injury. A When setting the pads and modules, please pay close attention in regards to the handling and setting of cables. Feet may become entangled in the cables resulting in falls. /e If thi s symbol is igno red and the equipment is used improperly, there is a danger of injury to r* a i itiom persons handling the equipment, and material CAUTION damage could occur. 0 Do not put your hands or feet under the foot pedal or foot switch. They may be pinched resulting in injury. A Watch your fingers when adjusting clamps. They may become pinched resulting in injury. A Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers. 0 Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. * Specifications are subject to change without notice. ÜYAMAHA YAMAHA CORPORATION RO.Box 1, Hamamatsu, Japan Printed in Taiwan F ■ RS100+Pad Grouping: Setup Example * Please use a snare stand for setting the snare drum pad. • Pad and Drum Trigger Grouping (option) ©DTXTREME Drum Trigger Module ©RHP120SD Snare Type Real Head Pad (12inch) ©RHP120 Real Head Pad (12inch) ©RHP100 Real Head Pad (10inch) ©RHP80 Real Head Pad (8inch) ©TP80S/TP80 Drum Pad ©PCY80S/PCY80 Cymbal Pad ©PCY10 Trigger Pad ®KP120 Real Head Kick Pad ©HH80A Hi-hat Control Pedal ©Snare Stand *SS-642 etc. ©Foot Pedal *DFP-880 etc. ■ Please use for additional pads. • CYAT100 Cymbal Attachment • TPCL100 Tom Holder ■ RS100 Assembly * A screw driver (+ or -) is necessary to complete the assembly. Please make sure that the fixing bolts on each part, such as clamps, pads, etc. are firmly tightened. Bolts that are too tight or too loose may result in damage to the part or the part dropping. Please use caution. Attach the Center Pipe Assembly A [d and the Center Pipe Assembly B H to the upright pipes of the Side Assembly A [a and Side Assembly B [b . Attach the Side Arm [F| to the pipes of the side Assembly B [b and the Side Assembly C [o . Center Pipe Assembly A [d] Side Assembly A [A] Attach the Module Holder M I 3-1 Attach the Module Holder Clamp \±\ to the pipe of the Side As sembly C [C 3-2 Insert the Tom Holder [g into the Module Holder Clamp HO, and tighten the fixing screw. 3-31 Attach the DTXTREME to the Module Holder [h . Using a screw driver and the supplied screws, attach the Module Holder [h to the screw holes on the bottom of the DTXTREME. 3-4 Attach the Module Holder [h , with the DTXTREME attached, to the Tom Holder [g . Module Holder [h] ^ Step Step 3-3 Side Assembly C [C_ 3-4 * Step [3-2 Tom Holder [q] ^Module Holder Clamp IT] Attach the Tom Holders [g 4-1 | Insert the Tom Holders [G into the Holder Clamps, align and tighten the fixing screws. Attach the Cymbal Holders 0 | 5-1 Insert the Cymbal Attachments into the upright pipes of the Side 4-2 Check the position and attach the Re...