Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
Drum trigger module clamp a Left leg b Drum trigger module clamp a Left leg b Holder clamp Hi-hat holder Continued on other side Mounting snare and tom pads . Mounting the snare pad 1. Attach the clamp bolt to the snare pad and provisionally tighten (by 5 or 6 turns). 2. Mount the snare pad on the rack’s clamp rod. As shown below, ensure that the rod section is fully inserted into the pad’s mounting hole, and then fully tighten the clamp bolt. 3. If necessary, use clamp bolts A to E to adjust the height and angle of the snare pad. When doing so, be sure to adjust one bolt at a time (i.e., loosen a bolt, adjust the pad, and then retighten before loosening another). . Mounting the tom pad 1. As with the snare pad, attach the clamp bolt to each of the three tom pads and provisionally tighten (by 5 or 6 turns). 2. Mount the three tom pads on the rack’s clamp rods. As shown below, ensure that the rod section is fully inserted into each pad’s mounting hole, and then fully tighten the clamp bolt. 3. If necessary, use clamp bolts A to D to adjust the height and angle of any of the pads. When doing so, be sure to adjust one bolt at a time (i.e., loosen a bolt, adjust the pad, and then retighten before loosening another). XP80 DTX540K: XP70 DTX520K: TP65 Clamp bolt (to be tightened in the direction shown) Snare pad (rear side) Insert Snare pad Rod section Clamp rod Clamp bolt Clamp bolt C Clamp bolt A Clamp bolt E Clamp bolt D Clamp bolt B Support plate Tom pad Clamp bolt Insert Rod section Clamp rod Clamp bolt C Clamp bolt D Clamp bolt B Clamp bolt A Mounting the drum trigger module, cymbal pads, and hi-hat pad . Mounting the drum trigger module 1. Attach the module stand (provided) to the underside of the drum trigger module using the module stand fastening screws. 2. Place the module stand inside the holder clamp and tighten the clamp bolt to secure in position. .Mounting the cymbal and hi-hat pads 1. Using a tuning key, loosen the stopper’s key bolt. 2. Remove the wing nut, the two felt pads, and the bolt cover from the cymbal holder. 3. Place the stopper on the cymbal holder. * If the key bolt was not sufficiently loosened in Step 1 above, it may not be possible to pass the stopper over the cymbal holder’s shaft. In such a case, loosen the key bolt as much as possible without removing it. 4. Replace the bolt cover. * When assembling the bolt cover, turn until it no longer rotates. 5. Secure the stopper in place. With the stopper making full contact with the bottom surface of the bolt cover, tighten the stopper’s key bolt using a tuning key. 6. Place one of the felt pads removed in Step 2 on the cymbal holder. 7. Mount the pad unit on the cymbal stand. Lower the pad unit into place with the cymbal holder’s shaft passing through the central hole of the cup section. When mounted, the stopper’s pin should rest inside the pad unit’s smaller hole. * If you were to play a cymbal pad without the stopper’s pin positioned inside the smaller hole, the pad could rotate, causing the cable to be pulled out. It is very important, therefore, to ensure that the stopper is secured as described in Step 5 above. 8. Assemble the felt pad that came with your pad unit. * The second felt pad removed from the cymbal holder in Step 2 above is not required for assembly of your pad unit. 9. Tighten the wing nut to secure the pad unit to the cymbal holder. Cymbal pad: PCY100 Drum trigger module Hi-hat pad: PCY100 Cymbal pad: PCY135 Module stand fastening screws Module stand Drum trigger module (back side) Front of module Clamp bolt Drum trigger module + module stand Insert Holder clamp Tuning key Key bolt Stopper Cymbal holder Felt pads Bolt cover Wing nut Cymbal holder Stopper Bolt cover Cymbal holder Bolt cover Stopper Full contact Full contact Bolt cover [Cymbal pad] [Hi-hat pad] Pad unit Felt pad that came with pad unit Cymbal holder Felt pad Bolt cover Pad unit Stopper Pin Wing nut Stopper’s pin Smaller hole Position the hi-hat controller and kick pad as desired, referring to the standard assembly example on the other side. Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can place the packages' cardboard boxes on the floor under the hi-hat controller and kick pad to protect it from damage. Connect the pads to the drum trigger module. As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module. Connect the drum trigger module to a power supply. This completes the assembly procedure. * For information about tuning the power on/off, checking the actual sound, and other subsequent steps, refer to the Setting Up section of the owner’s manual that came with your drum trigger module. Assembling the kick pad 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from scratching. 2. Remove the wing bolts, spring washers, and washers from the kick pad body, and line up each set nearby in the orde...
Other models in this manual:Musical Instruments - DTX520K (2.63 mb)