Votes - 4, Average rating: 3.5
(
)
)
|
Other manuals for this model:
manual abstract
Other power sources may damage the device. * Before connecting the AC adaptor, make sure that the polarities of the plug and the jack match (—+). * The PITCH indicator at the extreme left will light up unless the power switch is turned OFF. ► For maximum battery life, always be sure the tuner is turned OFF when not in use. ► To prevent possible damage due to leakage of battery fluid, remove the battery from the tuner if it is not to be used for an extended period of time. ► Do not subject the tuner to strong physical shock or vibration. Do not use excessive force on any of the parts. ► Never use solvents such as benzine or thinner to clean the tuner. Wipe clean with a soft, dry cloth. COMPONENTS ©PITCH INDICATORS O POWER SWITCH .©DC 9V JACK ©OUTPUT JACK ©INPUT JACK ©NOTE INDICATORS / \ '©MICROPHONE © PITCH SWITCH © NOTE SWITCH ■ SPECIFICATIONS Indicators : NOTE Indicators, PITCH Indicators Tuning Notes : Guitar 6E, 5A, 4D, 3G, 2B, 1E Bass 4E, 3A.2D, 1G Precision :±1cent Standard Pitch Range : A4 = 436 Hz — 444 Hz (1 Hz steps) : Battery Check : INPUT, OUTPUT, DC 9V : 9V dry cell battery (006P or 6F22) or YAMAHA AC adaptor (AC-05UC or AC-320UC) : 127 x 63 x 28.5 mm (5" x 2-1/2" x 1-1/8") : 127 g (4.5 oz) with battery : 9V dry cell battery (6F22) x 1 6E 5A 4D 3G 2B 1E Added Function Jacks Power Source Dimensions (WxHxD) Weight Accessory ■ TUNING PROCEDURES • Auto Tuning (AUTO) In AUTO mode, the tuner will automatically select the note closest to the tone input for tuning. This is convenient for tuning during musical performances. 1. For electric guitars and basses, connect the guitar cord to the INPUT jack ©. (At this time, the OUTPUT jack © can be connected to an amplifier in preparation for tuning during a performance.) For acoustic guitars, place the guitar sound hole near the built-in microphone ©. * The built-in microphone © cannot be used when there is a plug in the INPUT jack ©. 2. Turn the power switch O to the “AUTO” position. 3. If desired, press the pitch switch© to select the standard A4 pitch. (Refer to the Pitch Selection section for details.) 4. Pluck the string to be tuned. The appropriate indicator © will light up for the tuning note. (Do not pluck two or more strings at the time.) 5. If the wrong indicator light is on, adjust the guitar tuning peg until the correct light comes on. 6. Adjust the guitar tuning peg untill the pitch indicator © only at the center (440) light up. 7. Repeat steps 4 through 6 to tune the other strings. The “440” indicator only should light up. BASS 4E GUriAR 6E О The appropriate indicator for the plucked tuning note shopuid lights up. — 6E -(4E) ►SA- PA) ►4D- (2D) ► 3G -(1G) • Manual Tuning (MANL.) In MANL. mode, each note must be individually selected as needed. This mode is most commonly used to tune instruments before musical performances. 1. Similar to AUTO mode, connect the electric guitar or bass cord to the INPUT jack©. For acoustic guitars, place the guitar sound hole near the built-in microphone ©. 2. Turn the power switch © to the “MANL.” position. 3. If desired, press the pitch switch© to select the standard A4 pitch. (Refer to the Pitch Selection section for details.) 4. Press the note switch © to select the desired tuning note. The indicators © for the tuning notes will light in sequence (as shown in the pattern right) each time the note switch is pressed. 5. Pluck the string to be tuned and adjust the guitar tuning peg until the pitch indicator© only at the center (440) lights up. 6. Repeat steps 4 and 5 to tune the other strings. ■ PITCH SELECTION Recently, it has become common to slightly raise the standard pitch when tuning musical instruments. The standard pitch also depends on the region and the era. To conform to the current standard and to harmonize with other instruments, the standard pitch must be changed from time to time. • Pitch Selection Method 1. Turn the power switch © to the “MANL." or “AUTO” position. Press the pitch switch © once to enter pitch selection mode. An pitch indicator © will flash at one of the standard pitch settings (A4: 436 — 444 Hz). While the pitch indicator © is flashing, press the pitch switch©. The pitch indicators© will flash in sequence (as shown in the pattern below) each time the pitch switch © is pressed. Each pitch indicator © step represents a 1 Hz change in standard pitch. 436 — 437 — 438 — 439 — 440 — 441 — 442 — 443 — 444 2. 3. Г □ 4. Select the desired standard pitch. When the pitch switch© has not been pressed for about 2 seconds, the tuner will automatically return to tuning mode. * The standard pitch set as above is effective in both "AUTO” and “MANL." modes unless the power switch Q is turned "OFF”. If the power switchO is turned from “OFF” to "AUTO” or "MANL.”, the standard pitch will be reset at 440 Hz and the pitch indicator will be flashing for about two seconds. Once the standard pitch (A4) is set, you have only to tune each...