Votes - 6, Average rating: 4.2
(
)
)
|
manual abstract
In standard driver mode, audio signals are transferred between the UA-5 and the computer at a resolution of 16 bits and sampling frequencies of 44.1/48 kHz. Select this mode if you are using an application that uses MacOS’s own functionality, such as an application that uses the computer’s CD-ROM drive to play back CD-audio, or an application that uses the software synthesizer included with MacOS. The standard driver included with Mac OS does not support ASIO. Note also that the use of Mac OS 8.6 is not supported. Installing the special driver Installing the audio driver 35 Getting Connected and Installing Drivers (Macintosh) If you want to use the UA-5 in Advanced mode, proceed to Installing the special driver (p. 35). If you want to use Standard driver mode, proceed to Installing the OS-standard driver (p. 38). Switching between Advanced mode and Standard driver mode If you first install both the special driver and the standard driver, you will be able to switch between Advance and Standard driver modes by operating the UA-5's ADVANCE (mode select) switch. * In order for the setting of the ADVANCE (mode select) switch to take effect, you must exit all sequencer software and other applications that use the UA-5, switch off the UA-5, then turn it back on again The location for installation will depend on your system. Make sure that the startup disk for the system you are currently using is selected. 1 Exit all currently running software (applications). If you are using a virus checker or similar software, be sure to exit this as well. 2 Prepare the CD-ROM. Insert the UA-5 Driver CD-ROM into the CD-ROM drive. 3 In the CD-ROM, double-click the UA-5 USB Installer E icon. 4 Verify the installation location, and click [Install]. Getting Connected and Installing Drivers (Macintosh) 5 If a message like the following is displayed, click [Continue]. The other currently running applications will exit, and installation will continue. 6 A dialog box will indicate Installation completed. Click [Restart] to restart your Macintosh. 7 Set the UA-5’s ADVANCE (mode select) switch to the ON position. 8 Switch ON the UA-5’s Power switch. Connect the AC adaptor to the UA-5's AC adaptor jack, and insert the AC adaptor's plug into an AC power outlet. Then, turn on the power of the UA-5. Installing the ASIO driver This section explains how to install the ASIO driver that allows the UA-5 to be used by your sequencer software or audio editing software. For details on installation and settings of the ASIO driver, be sure to also read the English-ASIO- Setting ASIO Driver-E document on the UA-5 Driver CDROM. The ASIO driver of the UA-5 supports the following audio input/output channels. • Audio input....... 24/16 bit1 stereo ch. (2 monaural chs.) • Audio output .... 24/16 bit1 stereo ch. (2 monaural chs.) This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. ASIO (Steinberg Audio Stream In/Out Interface) This is an audio interface standard promoted by the Steinberg Corporation. When the UA-5 is used with ASIO- compatible software, the synchronization precision will be improved, allowing a more sophisticated music production environment. 37 Getting Connected and Installing Drivers (Macintosh) Here we will explain how to install the ASIO 1.0 16 bit- compatible driver. If your ASIO-compatible software supports ASIO 2.0 or recording/ playback of 24 bit audio data, using the following drivers will provide a higher quality environment. ASIO-compatible software ASIO2.0-compatible 24 bit compatible Driver to use . . UA-5 ASIO 1.0 16 bit . . UA-5 ASIO 1.0 24 bit . . UA-5 ASIO 2.0 16 bit . . UA-5 ASIO 2.0 24 bit The Audio setting dialog box will be named differently depending on your software. For details refer to the manual of your software. Getting Connected and Installing Drivers (Macintosh) Here we will explain how to install the ASIO 1.0 16 bit- compatible driver. If your ASIO-compatible software supports ASIO 2.0 or recording/ playback of 24 bit audio data, using the following drivers will provide a higher quality environment. ASIO-compatible software ASIO2.0-compatible 24 bit compatible Driver to use . . UA-5 ASIO 1.0 16 bit . . UA-5 ASIO 1.0 24 bit . . UA-5 ASIO 2.0 16 bit . . UA-5 ASIO 2.0 24 bit The Audio setting dialog box will be named differently depending on your software. For details refer to the manual of your software. 1 From the [Driver][ ASIO] folder of the CD-ROM, copy [UA-5 ASIO1.0 16bit] to the [ASIO Drivers] folder within the folder of the ASIO-compatible software you are using (e.g., Cubase VST, Logic Audio, Digital Performer, or Metro). 2 Start up your ASIO-compatible software (e.g., Cubase VST, Logic Audio, Digital Performer, Metro). 3 Open the Audio setting dialog box of your ASIO- compatible software, and select [UA-5 ASIO 16bit] as the ASIO Device. Getting Connected and Installing Drivers (Macintosh) Installing the OS-stand...